Height Of The CargoGlide 2200XL Sliding Tray

Question

Question:

how high is the bed of the CargoGlide over the pickup bed?

asked by: Bill

0

Expert Reply:

The CargoGlide 2200XL Sliding Tray for Trucks # cg2200xl-9548 is going to sit approximately 4" above the bed of your 2003 Dodge Ram.

expert reply by: Kevin C

0

Answer 1

The overall length of the tray is 95 inches and the width is 48 inches. The deck height is 4-1/2 inches and the lower side rails are 4-1/2 inches and the higher side rails are 8-1/2 inches. We can certainly get more dimensions for the CargoGlide…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Yes, you can replace your current Lippert Equa-Flex equalizers with the MORryde AllTrek 4000 Equalizers #MR29DR on your 2018 Highland Open Range. The yellow octagons on the front and rear are a for correcting the alignment of the axles and are not…

view full answer...

Answer 6

Hey John, Thanks for the purchases and you have everything you need except the wedge. I verified directly with Reese that the correct wedge to use with the Demco Recon 5th Wheel Trailer Hitch #DM8550043 and Reese Sidewinder #RP34FR is the following:…

view full answer...

Answer 7

Gen-Y's calculation for pin weight is a safe guess, but isn't the most accurate so the only way you'll get the correct capacity Gen-Y 5th Wheel Pin Box is to fully load the trailer and go to a commercial scale to measure the pin weight.…

view full answer...

Answer 8

Since you have a tandem axle trailer rated for 10,500lbs the 6-Leaf Double-Eye Spring for 5,300-lb Trailer Axles #e76SR are going to be the closest leaf springs we have to that weight capacity. These springs measure 24-7/8" from center of eye to…

view full answer...

Answer 9

If you are going to install two of the MORryde X-Factor Crossmembers #MR33WR on your tandem axle trailer Alan you would want to install them on the front and rear hangers. You can install a third one if you want on the middle hanger as well for even…

view full answer...

Answer 10

Hi Robert, The Curt Pintle Hook #C45908 would require that your EZ Loader boat trailer has a lunette ring for the coupler. From what I can see the 26-30ET should have a surge brake coupler that would couple to a standard ball mount. You'll need…

view full answer...

Answer 11

As long as the RBW Lil' Rocker mounts to industry standard base rails you'll need the Curt Adapter Rails #C29BR that fit in the OEM puck system on your 2019 Ram 2500 and give you a standard base rail connection. I'm attaching a photo…

view full answer...

Answer 12

The Air Lift LoadLifter 7500 XL Air Helper Springs #AL57531 will fit your 2022 Ram 3500 Mega Cab with single rear wheels. This is the extra heavy duty 7,500 lb kit so it is most commonly used on dually trucks, but it will fit single rear wheel models…

view full answer...