Will BAK Revolver X4s Tonneau Cover Work with Putco Locker Truck Bed Rails on 2022 Ram 15000 Classic

Question

Question:

Will this work with the BAK Revolver X4S tonneau cover?

asked by: Nathan

0

Expert Reply:

The BAK Revolver X4s Hard Tonneau Cover part # BAK44ZR which is a fit for a 2022 Ram 1500 Classic with 5-1/2' bed mounts inside the bed rails and the Putco Locker Truck Bed Side Rails part # P88862 mounts inside the stake pockets so they should in theory work together. That said, this isn't something we nor BAK or Putco tests for.

expert reply by: Conner L

0

Answer 1

The first thing you would have to do is remove the bars. This can be done by using a 5mm Allen wrench and unscrewing the bolt underneath each foot. Then you would remove the legs from the base. I would use some lube on the locking levers just in case…

view full answer...

Answer 2

I have a solution for you, but because of the weight of your e-bike, you're going to be extremely limited when it comes to options for carrying it on the roof of your vehicle. The best solution to carry your bike on your roof rack is the Inno…

view full answer...

Answer 3

The weight capacity of the Rhino-Rack Vortex Aero Crossbars part #RRVA165B-2 is 165 lbs which is for both bars and the weight must be evenly distributed. If you're looking for more, the Rhino-Rack Heavy-Duty Roof Rack Crossbars part #RB1650B-2…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Rhino Rack, if you were to go with the shorter bars, you'll only have 1-1/4 inch of leeway on each side which isn't enough in their opinion. I'd recommend going with the 71 inch bars so you'll be certain of a good fit. As…

view full answer...

Answer 8

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 9

I have a Yakima crossbar setup that is compatible with the Retrax Pro XR Tonneau Cover on your 2021 Toyota Tacoma, however, the Yakima Bedrock is not compatible and the 60" crossbars would be too short anyways. I recommend going with the…

view full answer...

Answer 10

Yes. You will need to use everything included with the Rhino-Rack Roof Rack for Thule and Yakima Tracks - 2 Heavy-Duty Crossbars - Black - 65" #Y01-140B-NT to install into the tracks you have pictured. The bases of the legs mount right into the…

view full answer...

Answer 11

I took a look at your order and it was the Rhino-Rack Roof Rack for Factory Tracks - 54" Bars #Y02-480B-NT which is too short for the 63 inch spacing on your truck. For that spacing you will need the following: - Rhino-Rack Roof Rack for Factory…

view full answer...

Will BAK Revolver X4s Tonneau Cover Work with Putco Locker Truck Bed Rails on 2022 Ram 15000 Classic

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching