Replacement Parts for Curt Curt TruTrack Weight Distribution System

Question

Question:

hello..i bought a hitch and i am missing some parts..It came from a 2nd party ..it is a curt 17501 ..im missing all the nut and bolts and the adjustable shank the snap up handle and the spring bar support bracket.i think thats it..thankyou for the help.

asked by: Gary U

0

Expert Reply:

We can definitely help you get the right parts for your Curt TruTrack Weight Distribution System w/ Sway Control # C17501. We have the following available:

-Replacement L-Pins and Clips for Curt TruTrack Weight Distribution System w/ Sway Control - Qty 2 # C17513

-Curt Weight Distribution Head Angle Adjustment # 17312

-Replacement Hardware Kit for Curt TruTrack Weight Distribution System w/ Sway Control - 15,000 lbs # C17554

-Replacement Spring Bar Lift Tool for Curt TruTrack Weight Distribution System w/ Sway Control # C17512

-Replacement Frame Brackets for Curt TruTrack Weight Distribution System w/ Sway Control # C17508

-Replacement Trunnion Spring Bar for Curt TruTrack Weight Distribution System - 1,500 lbs TW # C17537

-Replacement Head for Curt TruTrack Weight Distribution System w/ Sway Control - 15,000 lbs # C17509

-Curt Adjustable Weight Distribution Shank - 8" # C17100

These parts should cover everything you're looking for. I listed some additional parts just in case you find out you're missing something else. The shank listed above is the closest to the original, but more are available using the link below if you need a different rise/drop.

I have attached an installation video below, along with the written instructions for the TruTrack for your reference.

expert reply by: Robin H

0

Answer 1

The Replacement Trunnion Spring Bar for Curt TruTrack Weight Distribution System #C17537 has the following dimensions you asked about: - Bar Length 35" - Hole Location 7/8" From Edge - Hole Size 1/2"

view full answer...

Answer 2

I spoke with a representative of Curt who told me that if you needed a weight distribution system with more capacity than the #C17500 you would have to part ways with it and replace the whole system with the TruTrack #C17501, which has a total tongue…

view full answer...

Answer 3

The two Curt systems you have are very similar but to swap bars between the two you'd have to also swap the heads since the bars are different sized. So for a head you'd need the part #C17509 and the bars #C17537 and you'd have upgraded…

view full answer...

Answer 4

For your Curt TruTrack Weight Distribution System (10,000/1,000 pounds) #C17500 the correct replacement spring bar is the part #C17536. The shorter 28-1/2" bars that you currently have are no longer made. This replacement bar measures 35 inches…

view full answer...

Answer 5

There isn't any indication on the bars, like how Blue Ox uses the "dot" system to signify weight ratings. Curt assigns their trunnion bars are to the head unit of the WDS. For instance the Replacement Trunnion Spring Bar for Curt…

view full answer...

Answer 6

The best Curt TruTrack Weight Distribution System for a 7,000 lb trailer is part #C17500 which is rated for 8,000 lb - 10,000 lb trailers. The trailer once loaded should be right in the middle of the system or just slightly below which will lead to…

view full answer...

Answer 7

The Curt TruTrack #C17500 and the Curt TruTrack #C17501 actually use different head units too so you would need 2 of the Replacement Trunnion Spring Bar #C17537 as well as the 15K Replacement Head for Curt TruTrack Weight Distribution System #C17509.…

view full answer...

Answer 8

By rods I believe you are referring to the spring bars, and the length is 35-9/16 inches of the Replacement Trunnion Spring Bar for Curt TruTrack Weight Distribution System - 1,500 lbs TW #C17537.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Hey Travis, congrats on the new 2024 Jayco Flight 284BHS! Your travel trailer looks to have a GVWR of 7,950 lbs so I recommend going with the Equal-i-zer Weight Distribution w/ 4-Point Sway Control #EQ37121ET and pairing it with the Shank…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...