Length of 1,500 lb Curt TruTrack Trunnion Spring Bar

Question

Question:

What are the lengths of the two rods. I had a set but the one I had in was a diffrent length than both of them.

asked by: Cody D

0

Expert Reply:

By rods I believe you are referring to the spring bars, and the length is 35-9/16 inches of the Replacement Trunnion Spring Bar for Curt TruTrack Weight Distribution System - 1,500 lbs TW # C17537.

expert reply by: Kyle S

0

Answer 1

The Replacement Trunnion Spring Bar for Curt TruTrack Weight Distribution System #C17537 has the following dimensions you asked about: - Bar Length 35" - Hole Location 7/8" From Edge - Hole Size 1/2"

view full answer...

Answer 2

The two Curt systems you have are very similar but to swap bars between the two you'd have to also swap the heads since the bars are different sized. So for a head you'd need the part #C17509 and the bars #C17537 and you'd have upgraded…

view full answer...

Answer 3

We can definitely help you get the right parts for your Curt TruTrack Weight Distribution System w/ Sway Control #C17501. We have the following available: -Replacement L-Pins and Clips for Curt TruTrack Weight Distribution System w/ Sway Control -…

view full answer...

Answer 4

The best Curt TruTrack Weight Distribution System for a 7,000 lb trailer is part #C17500 which is rated for 8,000 lb - 10,000 lb trailers. The trailer once loaded should be right in the middle of the system or just slightly below which will lead to…

view full answer...

Answer 5

For your Curt TruTrack Weight Distribution System (10,000/1,000 pounds) #C17500 the correct replacement spring bar is the part #C17536. The shorter 28-1/2" bars that you currently have are no longer made. This replacement bar measures 35 inches…

view full answer...

Answer 6

I spoke with a representative of Curt who told me that if you needed a weight distribution system with more capacity than the #C17500 you would have to part ways with it and replace the whole system with the TruTrack #C17501, which has a total tongue…

view full answer...

Answer 7

The Curt TruTrack #C17500 and the Curt TruTrack #C17501 actually use different head units too so you would need 2 of the Replacement Trunnion Spring Bar #C17537 as well as the 15K Replacement Head for Curt TruTrack Weight Distribution System #C17509.…

view full answer...

Answer 8

There isn't any indication on the bars, like how Blue Ox uses the "dot" system to signify weight ratings. Curt assigns their trunnion bars are to the head unit of the WDS. For instance the Replacement Trunnion Spring Bar for Curt…

view full answer...

Answer 9

Hey Paul, I spoke with Curt and they stated that the Replacement Trunnion Spring Bar for Curt TruTrack Weight Distribution System #C17535 would only be compatible with the #C17499. The Curt TruTrack 4P Trailer Mounted Weight Distribution System w/…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Length of 1,500 lb Curt TruTrack Trunnion Spring Bar

Product Page this Question was Asked From

Continue Researching