Replacement Nev-R-Lube 6k Trailer Hub Bearing

Question

Question:

You have this bearing listed for 3500 and 4000 lb axles. What new-r-lube bearing fits 6000 lb Dexter axles?

asked by: Rene S

0

Expert Reply:

The Dexter Nev-R-Lube 6k hubs use 42 mm bearings so the correct replacement is the part # 31-73-3.

expert reply by: Jameson C

0

Answer 1

We currently offer the Dexter Nev-R-Lube Bearings in a few different sizes, 35MM part #31-72-3, 42MM part #31-73-3, or 50MM part #31-71-3. Please note, these are referring to the inner diameter of the bearing. In order to find the correct one you can…

view full answer...

Answer 2

Thank you for all that info, and replacing the equalizers, as well as upgrading the suspension hardware is going to be the best option for you. The correct size equalizer, as well as the suspension kit that I recommend is the following: - Curved…

view full answer...

Answer 3

Assuming that your shackle links measure 2-1/4 inches center hole to center hole, the ideal replacement for your existing #A2252CB-GALV suspension equalizers would be the #K71-653-00 E-Z Flex kit from Dexter Axle which is good for axle capacities up…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 6

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...

Answer 9

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

In order to verify the spindle dimensions so that you can pick out the correct hub/drum you have to get exact dimensions. For that you need to use a digital caliper like part #PTW80157. For how old your trailer is this is especially important as the…

view full answer...

Answer 12

You will need to measure the diameter of the spindles where the seal and bearings ride. Check out the picture I attached that shows where this is. You will need an exact measurement so either a digital or dial caliper will be needed. To pick out the…

view full answer...

Replacement Nev-R-Lube 6k Trailer Hub Bearing

Product Page this Question was Asked From

Continue Researching