Availability of Trailer Winch that Can Have Handle Install on Both Sides

Question

Question:

Can you switch the side that the handle is on on this winch? Or could it be mounted 180 degrees so that it pulls the other direction?

asked by: Nathan

0

Expert Reply:

The winch you mentioned part # 348776 can't have the handle mounted on both sides of it nor can it mount 180 degrees.

For a winch that you can move the handle to the left side you can use # FW16000101. This winch is specifically designed to allow the handle to be installed on either side easily so it would work the best for you.

expert reply by: Jameson C

0

Answer 1

For light requirements you have to look at the total length and width of the trailer along with its gross capacity. The 1987 Coleman Sequoia is 14 feet, 11 inches long and 6 feet, 8 inches wide. That makes the trailer right at 80 inches wide, but…

view full answer...

Answer 2

You could do either actually. The Optronics trailer taillight kit part #TLL160RK has a ring terminal for it's ground wire that you can either run back to the mounting hardware or cut off and wire to your ground wire. Personally I would probably…

view full answer...

Answer 3

It does not matter which mounting post of the Optronics Trailer Taillight part #TLL160RK that you run the ground ring terminal to. As long as it ends up making contact with the trailer frame that is all that matters.

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 9

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 10

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Availability of Trailer Winch that Can Have Handle Install on Both Sides

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching