Trailer Hitch Receiver For 2020 Nissan Altima

Question

Question:

You state there is no hitch for my 2020 Nissan Altima 4 dr sedan but you have a video installing one on the same vehicle. It is a curts hitch. What gives

asked by: David W

1

Helpful Expert Reply:

I'm not sure who stated there is no hitch for a 2020 Nissan Altima or what gives but there is a fit for a trailer hitch for your 2020 Nissan Altima, which is the Curt hitch you mentioned, at the following part number:

- Curt Trailer Hitch Receiver # C11352

expert reply by: Kyle S

1

Answer 1

I have confirmed that the Curt Trailer Hitch Receiver I - 1-1/4" #C11352 is a good fit for your 2014 Nissan Altima. This is a Class 1 hitch; there are currently no class 2 hitches available for the 2014 Nissan Altima. This is mainly due to the…

view full answer...

Answer 2

Hey there, unfortunately only a 1-1/4" receiver is available for your 2018 Altima - Curt #C11352; this has a weight capacity of 200lbs. There are a few cargo carriers that are compatible with this class 1 receiver, such as #C18110 which is a…

view full answer...

Answer 3

I believe I have an option for carrying 4 bikes with your Altima, but the thing about using a hitch adapter is that they cut the capacity of the hitch in half due to the increased leverage and movement the adapter creates. Since the hitch on your…

view full answer...

Answer 4

The only hitch we offer for your 2007 Altima is a Class I hitch, which has a 2000 lb towing/ 200 lb tongue weight (the maximum amount of weight that can be suspended from the hitch) capacity. Using an adapter would lower the tongue weight capacity by…

view full answer...

Answer 5

The recommended 2 inch Euro style ball mount for Curt trailer hitch #C11352 on a 2015 Nissan Altima is #C45572. I went out to the warehouse and pulled one to take some measurements. From the center of the pin hole to the part of the shank where it…

view full answer...

Answer 6

As you can see in the photo I assembled from captured images from the install video, the mounting flange of the hitch provides as much heat protection as the heat shield that is removed and discarded. The steel of the hitch mounting flange is much…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 10

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Trailer Hitch Receiver For 2020 Nissan Altima

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching