Mounting Hole Dimensions of Replacement Female Tie-Down Buckle # EX54560402

Question

Question:

Gentlemen, can you tell me the spacing/center to center of the mounting holes on your item # EX54560402? Thanks in advance for your help.

asked by: David M

1

Helpful Expert Reply:

The distance between the mounting holes of the Extang buckle part # EX54560402 that you referenced is 1-1/4 inches.

expert reply by: Jameson C

1

Answer 1

Sounds like you have an Extang Trifecta 2.0 and are in need of a replacement male bucket and strap kit part #EX54440400.

view full answer...

Answer 2

Thanks for the picture! Wthout knowing for sure what model tonneau cover you have, I can't say for sure. However, it does look like this strap will be compatible with your tonneau cover. As long as you have the 83-XXX series Extang Solid Fold 2.0…

view full answer...

Answer 3

The Replacement Tie-Down for Extang Solid Fold 2.0 Hard Tonneau Covers - Qty 1 #EX1024 that you were looking at measures 1-3/4" between bolt holes on the strap's tie-down and measures 1-1/4" between bolt holes on the clip. I attached…

view full answer...

Answer 4

If you check out the picture I attached for the part #PARTS-356A0009 you'll see how it installs.

view full answer...

Answer 5

I'm sorry to hear about your trouble. We have a tech who has made that same mistake. The problem he cited was the anchor on the other side of the screw spinning when trying to unscrew the strap, preventing the screws from loosening. If this is in…

view full answer...

Answer 6

I reached out to my contact at Extang and the correct replacement female tie-down buckle for your original SolidFold Tonneau Cover is the part #EX1018. While similar in appearance the Tie-Down Buckle #EX54560402 that you referenced only fits the 2.0…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 12

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Mounting Hole Dimensions of Replacement Female Tie-Down Buckle # EX54560402

Product Page this Question was Asked From

Continue Researching