What Is The Distance Between Bolt Holes On Replacement Tie-Down For Extang Covers EX1024?

Question

Question:

What is the distance to center between the two screw holes?

asked by: Elliott

0

Expert Reply:

The Replacement Tie-Down for Extang Solid Fold 2.0 Hard Tonneau Covers - Qty 1 # EX1024 that you were looking at measures 1-3/4" between bolt holes on the strap's tie-down and measures 1-1/4" between bolt holes on the clip. I attached photos to further illustrate this.

expert reply by: Andrew N

0

Dimensions Of Tie-Down
(click to enlarge)

Dimensions Of Clip
(click to enlarge)

Answer 1

Thanks for the picture! Wthout knowing for sure what model tonneau cover you have, I can't say for sure. However, it does look like this strap will be compatible with your tonneau cover. As long as you have the 83-XXX series Extang Solid Fold 2.0…

view full answer...

Answer 2

The Replacement Tie-Down #EX1024 for the Solid Fold 2.0 does not include mounting hardware. If you cannot use your current screws you will need to source four of the 8-18 x 5/8 PFH TEK #2 screws locally for replacements.

view full answer...

Answer 3

I'm sorry to hear about your trouble. We have a tech who has made that same mistake. The problem he cited was the anchor on the other side of the screw spinning when trying to unscrew the strap, preventing the screws from loosening. If this is in…

view full answer...

Answer 4

If you check out the picture I attached for the part #PARTS-356A0009 you'll see how it installs.

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 8

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 9

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

What Is The Distance Between Bolt Holes On Replacement Tie-Down For Extang Covers EX1024?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching