Recommended Brake Controller and Adapter for a 2010 Toyota Tacoma

Question

Question:

Hi Im looking for a brake controller to install in my 2010 Toyota Tacoma. It appears to be pre wired under the dash. I would need the cake too connect this as well It will be used for light duty towing, small pop up camper single axel

asked by: Mark P

0

Expert Reply:

For your 2010 Toyota Tacoma, I highly recommend the Redarc Tow-Pro Liberty Brake Controller item # RED24FR. This is a proportional brake controller that activates your trailer's brakes when your Tacoma decelerates. It has a unique installation method where the only visible portion is the control knob that's about the size of a nickel. The main unit is hidden away inside your dash to be completely out of the way and out of sight.

You will need two adapters to connect this controller to your Tacoma without splicing wires. The first is the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers item # 3040-P this will plug directly into your Tacoma's wiring harness.

The second adapter you'll need is the Redarc Tow-Pro Wiring Adapter for Tekonsha Brake Controller Harness item # 331-TPH-017. It will connect the Tekonsha adapter to the Red Arc Liberty Pro item # RED24FR.

The harness you need to install the Brake Controller Adapter item # 3040-P will be located underneath your dash, to left of the steering column, and taped to another harness near the emergency brake pedal.

I attached a picture below that will show you were to find the connector. If you do not have this plug then you do not have the towing package and will need to use the Universal Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item # RED69FR to complete the installation

expert reply by: Jerred H

0

Toyota Tacoma Brake Controller Plug
(click to enlarge)

Answer 1

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

Sure thing, I will go ahead and list out what you need for your 2023 Kia Sportage to add a 7-way for a brake controller so you can tow with the Curt Trailer Hitch Receiver #C94WR: - T-Connector Vehicle Wiring Harness with 4-Way Flat Trailer Connector…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Answer 10

The trailer brakes work on a separate circuit than the lights. You have a couple of options to control the electric brakes on the trailer. One option is to use an air over electric brake control, #HA100400C. This unit connects to the air brakes on…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Recommended Brake Controller and Adapter for a 2010 Toyota Tacoma

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching