What Size Lug Nut to Use with Aluminum Viking Series Valhalla Trailer Wheel # AX02550545BMMFL

Question

Question:

Do you have a lug nut reference for these?

asked by: Chris P

0

Expert Reply:

The Aluminum Viking Series Valhalla Trailer Wheel # AX02550545BMMFL that you referenced is designed to be used with the standard trailer lug nut size of 1/2-20 like the stainless steel part # KALN1375S.

expert reply by: Jameson C

0

Answer 1

You can pretty easily go from a 205/75-14 to a 15 inch tire size like 205/75-15 like with the #AM32395 without clearance issues. This will give you a slightly larger wheel and tire which will have a higher weight capacity. So you might gain a slight…

view full answer...

Answer 2

In most cases they are they same, but you have to find out what angle of cone you have. If you have the standard 60 degree cone then the #CE11051 would technically work just fine.

view full answer...

Answer 3

I recommend using the Trailer Wheel Lug Nut #AM90070 with the Provider ST225/75R15 Radial Tire w 15" Viking Aluminum Wheel #A225R6FPS. The stainless steel finish will match the wheel better than chrome against the wheels. This lug nut has a…

view full answer...

Answer 4

Trailer wheel lug nuts that are 1/2-inch inside diameter typically have a 20-TPI thread pitch (20 threads per inch). Most lug nuts also use a 60-degree-coned profile like #CE11051, but a 90-degree like #STN569 is also available for 9/16-inch studs.…

view full answer...

Answer 5

I have a possible solution, but Lionshead is phasing this wheel out which is why you can't find the 15" Bobcat with the 5 on 4-1/2 bolt pattern. The best option is to replace the wheel with a similar one like the Aluminum Viking Series…

view full answer...

Answer 6

The fastest powered a-frame jack we offer is the Phoenix Jack part #UF38-944055 that you referenced which can travel 10 inches in just 47 seconds. Depending on where you would mount the battery would determine if you'd need a battery box.

view full answer...

Answer 7

You can use a 3,500 pound capacity electric A-frame jack for your 7,500 pound travel trailer. The jack capacity does not need to match the weight of the trailer since the jack will not be lifting the weight of the entire trailer, only the…

view full answer...

Answer 8

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 9

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 10

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

What Size Lug Nut to Use with Aluminum Viking Series Valhalla Trailer Wheel # AX02550545BMMFL

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching