Correct Replacement Stabilizer Jack Support Arm for Lipprt Power Stabilizer Jack

Question

Question:

The legs that support the RV, I bent one where the bolt goes through with yellow brace.......... can I buy just the C-channel arm

asked by: Joe

0

Expert Reply:

It sounds like you're just needing the Replacement Electric Stabilizer Jack Support Arm for Lippert RV Jack # LC1134122 for your Lippert High-Speed Power Stabilizer Jack # LC298707.

This will replace one yellow support arm brace and measures 19-1/4" long x 1-1/2" wide. Also, please note that this part does not come with mounting hardware, so you'd need to use your original hardware or source it locally.

expert reply by: Bryce D

0

Answer 1

The direct replacement for your Lippert Model 113407 stabilizer jack is part #LC369774. I confirmed this with my contact at Lippert. It requires an easy bolt-on installation.

view full answer...

Answer 2

The ends of the support arms on your stabilizer jack should have a slight bend (see photo) but the arm itself should not be bent. If it is then it will need to be replaced. The correct one for you is the Replacement Electric Stabilizer Jack Support…

view full answer...

Answer 3

There are two replacement arms for the Lippert Components High-Speed Power Stabilizer Jacks, the Replacement Electric Stabilizer Jack Support Arm part #LC1134122 for yellow and part #LC1134121 for black. If you currently have yellow arms then you…

view full answer...

Answer 4

It sounds like the 12 volt circuit of the 7-way wiring is shorting out to the brake output circuit which is causing the brakes to lock up when the trailer is connected to the tow vehicle. This is most likely due to exposed wiring from when you…

view full answer...

Answer 5

The Electric Stabilizer Jack Support Arm #LC1134122 and Foot Assembly #LC157584 are the only replaceable parts for the legs on your Lippert PSX1 Stabilizer Assembly #LC298707. If you bent the leg itself you will need to replace the entire assembly.

view full answer...

Answer 6

Yes, the Demco Recon Gooseneck-to-5th Wheel Trailer Hitch Adapter #DM8550045 will easily connect to the B&W Turnoverball hitch ball you have in the bed of your truck.

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 12

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Correct Replacement Stabilizer Jack Support Arm for Lipprt Power Stabilizer Jack

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching