Is There A Replacement Leg For Lippert Electric Stabilizer Jacks PSX1?

Question

Question:

My trailer has the PSx1 stabilizer system. I bent one of the legs this last weekend bonehead move. Do you have the ability to sell a leg only for these?

asked by: Brian L

0

Expert Reply:

The Electric Stabilizer Jack Support Arm # LC1134122 and Foot Assembly # LC157584 are the only replaceable parts for the legs on your Lippert PSX1 Stabilizer Assembly # LC298707. If you bent the leg itself you will need to replace the entire assembly.

expert reply by: Bud M

0

Answer 1

The Replacement Single Zone Thermostat for Dometic RV Air Conditioners #DMC79FR is a single zone 3 wire thermostat like the one you are describing. I have attached the wiring diagram for this thermostat and the control box below for your reference.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Some newer cars, vans and small trucks, especially those with large, aftermarket tires, may require the use of Class S chains. Class S tire chains are designed for use on vehicles with restricted wheel well clearance. I have attached a photo that…

view full answer...

Answer 4

I am far from an expert on snowmobiles but one would have to think such a large truck with the correct tires and chains would be able to make it through up to 2' of snow assuming you have clearance on the vehicle. In regards to the type of tire…

view full answer...

Answer 5

Yes, your kick sensor for your hands free liftgate will still work after installing a Class III receiver on your 2024 Toyota RAV4 XSE. I have linked an install video near the bottom of the page for our etrailer Trailer Hitch Receiver #e23ZR being…

view full answer...

Answer 6

No, I am sorry we do not! To remove the Titan Chain Snow Tire Chains item #TC1555 you will disconnect the tensioning chain with red clips and the green hook, both on the outside of the tire and then the straight pin connector on the inside-facing…

view full answer...

Answer 7

There are two replacement arms for the Lippert Components High-Speed Power Stabilizer Jacks, the Replacement Electric Stabilizer Jack Support Arm part #LC1134122 for yellow and part #LC1134121 for black. If you currently have yellow arms then you…

view full answer...

Answer 8

There are not replacement legs available for the Lippert Components High-Speed Power Stabilizer Jack - White Switch Kit - 30" Lift #LC369774 which is the same as the 198641 you mentioned. You will need to replace the entire unit. The support arm…

view full answer...

Answer 9

If the actual leg of the stabilizer jack, like the Lippert High-Speed Power Stabilizer Jack #LC298707, is bent then you'll unfortunately have to replace the entire assembly. Lippert has a few replacement parts for this jack but I think the…

view full answer...

Answer 10

For your Lippert PSx1 Stabilizer, the Replacement Electric Stabilizer Jack Support Arm part #LC1134122 is what you need if you are looking to simply repair your jack. If instead you are looking to replace the entire unit then the Lippert Components…

view full answer...

Answer 11

The Lippert High-Speed Power Stabilizer Jack part #LC298707 would be an excellent replacement option for the now discontinued 337199 model. It does come with a new switch so you can either wire this up or reuse the existing, either way the switch…

view full answer...

Answer 12

The ends of the support arms on your stabilizer jack should have a slight bend (see photo) but the arm itself should not be bent. If it is then it will need to be replaced. The correct one for you is the Replacement Electric Stabilizer Jack Support…

view full answer...

Is There A Replacement Leg For Lippert Electric Stabilizer Jacks PSX1?

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching