Where Do 5th Wheel Rails Install in the Bed of a 2003 Ford F-250 Long Bed

Question

Question:

What is the measurement from the rear of the bed to the rear holes on a Ford F250 with a 8foot bed? Thanks!

asked by: Paul A

1

Helpful Expert Reply:

On your 2003 Ford F-250, if it has a gross vehicle weight of 8,500 pounds or less then from the rear edge of the bed to the back of rear most rail it is 29-1/4 inches.

Over 8,500 pound GVW and it is 33-1/2 inches to the back of the rear rail.

Once you have the rear rail in place use the hitch to place the front rail. I have linked the instructions for the Reese universal installation kit # RP30035. I have also linked a video showing a typical installation you can use as a guide.

expert reply by: Michael H

1

Answer 1

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 4

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 9

There are a couple of options that'll work great with your Lippert Turning Point Pin Box, however one hitch stands out to me more than others. Take a look at the: -Curt E16 5th Wheel Trailer Hitch - Slide Bar Jaw - 16,000 lbs #C16115 This 5th…

view full answer...

Answer 10

The recommendation for the 10" diameter lube plate on a B&W Companion 5th Wheel Trailer has come from the manufacturer of the fifth wheel hitch, B&W. The Lube Plate for Reese 5th Wheel Trailer Hitches part #RP83002 will work just fine…

view full answer...

Answer 11

I recommend using a Lube Plate #16721 over covering the Demco Recon 5th Wheel Trailer Hitch #DM8550043 in Grease #L74FR. The lube plate is much cleaner and you will not have to constantly clean off the dirt and apply new grease over time.

view full answer...

Answer 12

The pin weight of a 5th wheel trailer will usually be around 20% of the trailer's gross trailer weight (GTW) rating. The only real way to find the loaded pin weight of your 5th wheel trailer would require access to a commercial scale used to…

view full answer...