Correct Replacement Brake Pads for Dexter DB-35 Calipers

Question

Question:

I have a tandem axle boat trailer and looking to see if you have a replacement for a CYFC-ZD1-FF? This is the identifying stamp on the old brake pads.

asked by: Chris B

0

Expert Reply:

The correct replacement brake pads for the Dexter DB-35 Disc Brake Calipers is the Replacement Brake Pad for Dexter 10" Disc Brake Assemblies part # T4870900.

expert reply by: Conner L

0

Answer 1

Part AD2528E is a double-lip grease seal from NOK that cross-references to National seal part 470460. My research shows this seal has an inner diameter of 1.688-inches and an outer diameter of 2.560-inches. The nearest item we have is part…

view full answer...

Answer 2

The best way to remove a Bearing Buddy Bearing Protector like #BB2717 is pretty much what you've been doing. Because the fit inside the hub bore is pretty tight, you just have to take a rubber mallet (or wood block) and firmly tap it around…

view full answer...

Answer 3

There is no specific torque rating for the castle nut that holds your hub in place. We recommend tightening the castle nut down until it stops, and then backing it off to the next notch wheel the tang washer will fit into the castle nut. Over…

view full answer...

Answer 4

I have a few options for you to help with identifying the bearings on your trailer. The first and easiest method would be to crawl under the trailer and look for the axle tag on the beam. This should give an axle capacity which we can then use to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Correct Replacement Brake Pads for Dexter DB-35 Calipers

Product Page this Question was Asked From

Continue Researching