How To Find Correct Replacement Gas Shock for Outdoor Kitchen on Trailer

Question

Question:

I do not know the type of gas strut for the outdoor kitchen door on my 2019 Coachmen Catalina Legacy Edition. Which part is fit this one? Thanks,

asked by: Wayne

1

Helpful Expert Reply:

The best way to find the correct replacement shock for your outdoor kitchen is by measuring and noting the capacity. The Gas Shock part # 372-5300-20 for example measures 20" extended and 11.41" compressed with a 20 lb force. I have attached our full list below.

Unfortunately, we have no way to look up parts like this for any one specific trailer.

expert reply by: Conner L

1

Answer 1

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A typical RV entry door gas strut ranges from 10-20lbs in pressure. We carry both a 10lbs #372-5300-10 and 20lbs #372-5300-20 that you can use. Really it just comes down to preference and the climate. If you're in a windy climate going heavier…

view full answer...

Answer 4

There are many factors that go into selecting the correct gas shock, the easiest would be to simply match the new shock with the existing using any labels printed on the body. If none are present or you are adding a new one then you can use a formula…

view full answer...

Answer 5

The RV Cabinet Door Struts #37270555 that you mentioned is designed to install to a ball socket like #3691858. However, these cabinet door struts do include the necessary ball socket needed for installation.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

There should be a sticker or plate on the pin box itself that lists the manufacturer and model of the pin box. If it is not present then there are some measurements you can take to determine the model of the pin box. I have included a link that…

view full answer...

Answer 8

According to pages 248 and 249 there are no transmission issues when you flat tow your 2011 Ford Flex. If you have a front-wheel drive vehicle it can be flat towed or dolly towed like #RM-2000-1. An all-wheel drive vehicle can be flat towed or…

view full answer...

Answer 9

We do not carry Winnebago or Globrite lights. From what I could find using the numbers you provided, the closest option that we have is the Optronics LED Trailer Tail Light #STL78RPG which is 7-9/16" long x 3-5/16" tall x 3/4" thick.

view full answer...

Answer 10

I went out to our warehouse and pulled the wiring harness. The wire in the Optronics Wishbone 4-way Trailer Harness, #A20WB, is copper.

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

The Flint Hill Goods Square LED Brake Light Hitch Cover for 2" Hitches #FHG72VR would indeed be compatible with the #118384 on your 2012 Chevy Colorado. Using the turn signals will not cause the hitch cover to blink. The cover will light when…

view full answer...

How To Find Correct Replacement Gas Shock for Outdoor Kitchen on Trailer

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching