MORryde CRE3000 and Suspension Upgrade Kit for 2017 Grand Design Imagine 2150RB

Question

Question:

2017 grand design imagine 2150rb. Looking for correct cre3000 and wet bolt shackle . Looks like 35 inch wheelbase. Do you measure shackle length from bolt centers or total length?

asked by: Kimble

0

Expert Reply:

Your 2017 Grand Design Imagine 2150RB does in fact have a 35" wheelbase so the correct MORryde CRE3000 is the # MR27ZR. Unfortunately, Grand Design doesn't list the shackle length but I believe what you have is 2-1/4". This measurement is from center of hole to center of hole, or as you said the bolt centers. Go ahead and measure just to be sure. If you have 2-1/4" shackles you need the # MR46ZR and for 3-1/8" shackles the # MR76ZR.

expert reply by: Robin H

0

Answer 1

In order to choose the correct MORryde Shackle Upgrade Kit you'll need to know the length of your shackle straps. If you have 2-1/4" long shackle straps then you can use part #MR86ZR or if you have 3-1/8" long shackle straps…

view full answer...

Answer 2

In order to confirm fit of the MORryde Shock Absorbing Suspension Equalizers for Tandem Axle Trailers you'll simply measure the axle spread on center. If the axles measure 33" apart then use part #MR87ZR but if they are 35"…

view full answer...

Answer 3

Finding the correct MORryde equalizer kit will be pretty specific, so I cannot tell you which will be correct without knowing the wheel spacing and axle capacity, unfortunately. With that being said, if you have the trailer's VIN, you may be able…

view full answer...

Answer 4

When it comes to an axle weight rating of 3,500 pounds, the gross weight of the vehicle cannot exceed that weight rating by any circumstances. The only way to increase the payload weight is by installing new axles. Although, you must also consider…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but they…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...