Shackle Pin Hole Diameter of Curt Tow Strap Loop # C45832

Question

Question:

What is the pin hole diameter for the shackle?

asked by: Shawn G

0

Expert Reply:

I checked with Curt and the diameter of the pin hole for the shackle of the Curt Tow Strap Loop part # C45832 is 5/8 inch.

expert reply by: Jameson C

0

Answer 1

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 2

The newest Thule square crossbars are the same dimensions of the previous crossbars, which is 1-1/4 inch wide x 7/8 inch tall. Like you mentioned, the only difference between this generation of Thule square crossbars and the previous generation is…

view full answer...

Answer 3

Yakima has their Jetstream roof rack for your 2018 Ford F-150 Supercrew with the part numbers #Y00426, #Y28TR, and #Y06122 which I attached an install picture of on a truck with a panoramic roof just like yours.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 7

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Thanks for reaching out, Joe! I recommend using the Rhino-Rack Aero Bar Roof Rack for Camper Shells #Y02-480B which comes with 63" long tracks as well as 54" long crossbars which should give you a little bit of overhang on your canopy. Per…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 12

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Shackle Pin Hole Diameter of Curt Tow Strap Loop # C45832

Product Page this Question was Asked From

Continue Researching