Replacement Master Cylinder for Titan Model 6 Surge O Matic Actuator

Question

Question:

Will part # T1777405 work on a Titan Surge O Matic Model 6 Actuator

asked by: Ted

1

Helpful Expert Reply:

Yes, the replacement master cylinder kit part # T1777405 is the correct replacement for a Titan Surge O Matic Model 6 actuator.

expert reply by: Jameson C

1

Answer 1

The wiring that feeds the 12-volt accessory circuit on the 7-way trailer connector is of insufficient gauge to allow enough power to pass through to run a trailer mounted winch. The main function of that circuit would be for lighter-duty…

view full answer...

Answer 2

Even when stored in the somewhat controlled environment of a garage, tires are still subject to dry rot and flat spotting. Even if the tire tread has plenty of depth left and you can't see any cracking with the naked eye, the generally accepted…

view full answer...

Answer 3

I will be happy to explain resetting the breakaway lever on the Titan Model 6 actuator, #T4747200. The manual states: Resetting the Break-away Lever: (Refer to the parts diagram in the instructions linked to the right). When the break-away lever…

view full answer...

Answer 4

You are correct that disc brakes require an actuator with higher psi pressure than what is required by drum brakes. Drum brakes need pressure of 1000-psi but discs need 1500 to 1600-psi. You can convert your Titan Surge-O-Matic Model 6 actuator to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 9

Thank you for the pictures! For a replacement option I recommend the Dexter DX7.5L A-60 Brake Actuator w Electric Lockout - Bolt On - Disc - 2" Ball - Zinc - 7.5K #DX29FR to replace your current actuator. The #DX29FR has a 7500lb trailer weight…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Replacement Master Cylinder for Titan Model 6 Surge O Matic Actuator

Continue Researching