Replacement Axle-Less Suspension for a Boat Trailer

Question

Question:

I have a 1994 nitro bass boat with a trailstar trailer and need a new axle overall length is 92 spring distance is 73 1/2 is 3 hub face is 87 1/4 The trailer has surge brakes also looking for hubs and bearings Any help is appreciated!

asked by: Dennis M

0

Expert Reply:

I have a solution for you but we don't have any axles with a 92" length. Instead I recommend using the Timbren Axle-Less Trailer Suspension item # ASR3500S05. This axle-less suspension system will attach directly to your boat trailer's frame. It has a 3,500 lbs capacity.

expert reply by: Jerred H

0

Answer 1

Your 2020 Nitro Z20 has an average weight of 4,000lbs. For that weight I recommend using the 6,000lb Dexter E-Z Flex Suspension Kit #K71-652-00. You will want to verify this with the spacing or your current equalizer. This kit is designed to replace…

view full answer...

Answer 2

You will need the Dexter E-Z Flex Suspension Kit #K71-652-00 for your 2015 Nitro bass boats tandem axle trailer. These equalizers have the lower mounting holes spread 5-3/4" on center and as they have weight added to them the rubber cushion will…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 5

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 6

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but they…

view full answer...

Answer 7

Yes, axle spread and wheel base by definition are the same measurements. You will measure from the center of one axle to the center of the 2nd axle to determine what you axle spread is. This may be difficult as some wheels and covers will make this…

view full answer...

Answer 8

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...

Answer 9

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 10

The absolute best cushioned equalizer that fits the dimensions you mentioned having would be the MORryde ALLTREK 4000 part #MR89DR as this is only option to provide vertical and horizontal cushioning. This would make a big difference and you'd be…

view full answer...

Answer 11

The hangers you currently have on your trailer are ones I have run into before. That being said, I spoke with MORryde and the #MR27ZR will still fit your trailer, but there is a modification that will need to be made. You’ll have to trim according to…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...