Replacement Trailer Bearings for L68149, LM67048 and Seal # GS-1719

Question

Question:

Is this the right kit the bearings do not match

asked by: Ricky

0

Expert Reply:

The bearing kit part # BK2-100 matches one of your bearings and your grease seal but it does not match everything so it would not be the correct kit to use. Since we don't have a kit that has everything your best option would be to get the parts individually. So for bearings you'd need the # LM67048, the seal # 58846, and bearing # L68149.

expert reply by: Jameson C

0

Answer 1

For a kit that includes the bearings, races, and seal you'd want the part #BK2-100 for each hub. Then for caps you'd want the part #DC200L-DCRP. For a castle nut #165686 and for lug nuts #AM90070.

view full answer...

Answer 2

You will need to measure your axles first though. The axles we offer are 89 inches from hub face to hub face and 74 inches from spring center to spring center. If your axles match these dimensions the part #T3584F-EZ-8974 would be a great choice for…

view full answer...

Answer 3

From the information you gave me I would have to guess you have a #84 spindle rated for 3,500 lbs so the replacement bearing kit would be #BK2-100. I don't have a way to confirm this on my end though (even with the VIN since we don't have a…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...

Answer 8

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Answer 9

The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

The recommended lug nut torque for your 7,000lb axle depends on a few factors like wheel size, stud size etc. Check out the attached photo which shows the torque specs for a variety of applications. I see you were looking at the Dexter Nev-R-Adjust…

view full answer...

Answer 12

On Dexter 12" Nev-R-Adjust Electric Brake Assembly #23-458 the shoe pad thickness is 3/16 of an inch. Dexter says that you should replace the shoes if the material gets down to 1/16 of an inch thick or less.

view full answer...

Replacement Trailer Bearings for L68149, LM67048 and Seal # GS-1719

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching