Parts Needed To Add 7-Way and Brake Controller to 2016 Ford F-150 With Factory 4-Way

Question

Question:

I just bought a 2016 ford f 150. It came with a 4 pin plug. I pull many trailers and need to convert to 7 pin and have trailer braking and reverse lights. what items will i need to purchase to get this done. Also, are there any videos that might be helpful gettting this done?

asked by: John M

0

Expert Reply:

Since you have a factory 4-Way on your 2016 Ford F-150 we can get you completely setup with plug-and-play parts. To upgrade your connection to a 7-way you need the Tekonsha T-One Vehicle Wiring Harness # 118283. This is going to plug into the factory connection at the rear of your truck. I also recommend the mounting bracket # PK12711U and no-drill bracket # C57202 to hold the connector in place.

The only other thing you will need is a brake controller. I recommend the Redarc Tow-Pro Liberty # RED24FR. The Liberty gives you accurate and reliable braking while taking up minimal space in your cab. The main unit installs out of sight so only the control knob is visible. This also gives it a sleek factory appearance. The knob controls the braking power and acts as the manual override. As I said, this is a total plug-and-play setup so the brake controller can be installed using the factory port and the # 331-TPH-007.

I have attached an installation video for the wiring harness on a 2016 F-150 below, along with an installation video for the brake controller on an F-250 for your reference.

expert reply by: Robin H

0

Answer 1

On your 2016 Ford F-150 XLT, since your truck came with the factory 4 way flat, you will want to use the Curt T-Connector Vehicle Wiring Harness with 7-Way Trailer Connector #C56307 to add those other functions. The Replacement Multi-Tow 7-Way &…

view full answer...

Answer 2

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 10

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Parts Needed To Add 7-Way and Brake Controller to 2016 Ford F-150 With Factory 4-Way

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching