Correct Replacement for Dexter Grease Seal 010-004-00

Question

Question:

I have a dexter axle and a dexter hub Seal number 010-004-00 I cant find. What other seal number I can replace for my dexter hub and wheel bearing kit.

asked by: John D

1

Helpful Expert Reply:

The Redline Grease Seal part # 10-40 is what you need to replace a Dexter Grease Seal 010-004-00, they are the same dimensions. The only difference is that this new seal is a double lip and the one you have is a single, double has better protection than single so it's an upgrade.

expert reply by: Conner L

1

Answer 1

Grease Seal #RG06-050 has an inner diameter of 1.719" and outer diameter of 2.565", you mentioned you have grease seal 10-4 and it has a width of .5" but from my research it looks like a 10-4 seal has an inner diameter of 1.249"…

view full answer...

Answer 2

You can verify that the 10-19 grease seal included in Bearing Kit #BK2-100 is the correct one for your spindles by taking two measurements. First you want to measure the rear hub bore where the seal is inserted. The seal's outer diameter needs to…

view full answer...

Answer 3

We have the exact seal you would need. For a pair you would want the part #RG06-050. This is a double lip seal that would work great for you. Double lip seals aren't only for EZ lube spindles. They are just basically a better sealing design than…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

In order to verify the spindle dimensions so that you can pick out the correct hub/drum you have to get exact dimensions. For that you need to use a digital caliper like part #PTW80157. For how old your trailer is this is especially important as the…

view full answer...

Correct Replacement for Dexter Grease Seal 010-004-00

Product Page this Question was Asked From

Continue Researching