Will Correct Track Trailer Alignment Kit RR23QX Work w/ Tandem 7,000lb Axles?

Question

Question:

Will this work on a tandem axle gooseneck with 7k axles ?

asked by: Ryan

0

Expert Reply:

Sure will!

The Correct Track # RR23QX you looked at will work perfectly with the Tandem 7k axles on your gooseneck trailer giving you either a 1-1/4" or 2-1/4" lift depending on your needs.

expert reply by: Samuel C

0

Answer 1

I do have an option for you, but we do not recommend using lift blocks on trailers due to movement/damage they can cause overtime in trailer suspension. Instead since you already have the spring over the axle I recommend using the Correct Track…

view full answer...

Answer 2

The best ST235/80R16 Load Range G tire we offer is the Provider ST235/80R16 Radial Trailer Tire part #PRG80235. This is a radial tire ideal for long highway trips, has an 81 mph speed rating, and comes with a two year warranty. The tire has a max…

view full answer...

Answer 3

If you wanted to upgrade your trailer to an air ride suspension setup and also get a 2 inch lift we have the Lippert Air Ride kit part #LC1565391 which does just that. It will also make your trailer ride much smoother and improve braking. This in…

view full answer...

Answer 4

The Torflex Lift Kit - Tandem Axle - 3-1/8" Lift #K71-725-02 is designed for a #12 Torflex Axle. What you have here is a spring axle. In order to lift your trailer I recommend the Dexter Trailer Springs Over-Under Conversion Kit #K71-385-00.…

view full answer...

Answer 5

I sent your axle info to Dexter and they were able to determine that you have a set of 7k Dexter Torflex axles so the correct lift you need is the part #K71-725-02 which will give you a lift of 3-1/8 inches.

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Answer 8

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but they…

view full answer...

Answer 9

Thanks for the pictures! Since your 2022 Grand Design Reflection 303RLS came with the CRE3000 equalizers you will need three of the MORryde X-Factor Crossmember item #MR33WR. It looks like you have the standard 3" wide frame hanger so all of the…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Yes, going from a 4 leaf to a 6 leaf spring would add slightly to your ride height. For example, if the current 4 leaf spring has 3/8" thick leaves, and you go to a 6 leaf spring with 3/8" thick leaves, you would be adding 3/4" of…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...