Measurements Needed to Find Replacement Hubs

Question

Question:

Im wanting to put new hubs on an old running gear so i can put smaller tires on it plus it needs new anyhow What measurements would you need to help me find right hubs

asked by: Shane

0

Expert Reply:

There are a number of measurements you'll need in order to find the correct hubs, and you'll need to use a digital caliper to measure your spindle to the thousandths of an inch where the bearings and grease seal ride, like in the photo I added.

You will also need to know your axle capacity (which should be stamped on the axle itself) and wheel bolt pattern. If you aren't sure what your wheel bolt pattern is I have linked a help article below which details how to find it.

For example, if you have a 2,000 lb axle with a 5 on 4-1/2" bolt pattern, and your bearings are L44649 (1.063" inner diameter) you would use the Trailer Idler Hub Assembly for 2,000-lb Axles - 5 on 4-1/2 # AKIHUB-545-2-G-2K.

I have added a link below to our entire selection of hubs for you once you find this info, or if you get back to me with your bearing numbers or measurements I can try and find the right one for you.

expert reply by: Kyle S

0

Where to Measure Trailer Spindle
(click to enlarge)

Answer 1

The Spindle Grease Seal Set #BB60001 is specifically designed to fit on your 1" straight spindle using a Bearing #L44643 and 1.980 Bearing Buddy like Set #BB1980A-SS. The seal set includes 2 smooth stainless steel rings, 2 O-rings and 2 grease…

view full answer...

Answer 2

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 3

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 4

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 5

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 6

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 7

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Measurements Needed to Find Replacement Hubs

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching