Replacement Parts Available for etrailer 3,500 lb Trailer Axle

Question

Question:

Hi, Do you stock brake parts for these axles? If so, what part numbers for replacement drums, shoes, and magnets? Thanks

asked by: Wayne

1

Helpful Expert Reply:

For the etrailer axle part # e95SR we do have replacement hub/drums with part # AKHD-545-35-EZ-K, and for brake assembly set # AKEBRK-35, for brake shoes # AKBRKR-S-10, and magnet # AKBRKR-M10.

expert reply by: Jameson C

1

Answer 1

I definitely recommend replacing your 3,500 lb 26 inch leaf springs with the 26 inch 4-Leaf Double-Eye Spring for 4,000-lb Trailer Axles #e22YR. The 4,500 lb would be too stiff and your ride would suffer so the better option by far are the 4k…

view full answer...

Answer 2

We cannot move the spring seats here on our 89 inch axles like the #e95SR that you referenced and we only have options that are spaced 74 inches apart like this one. In order for you be able to use this axle you'd have to have new ones welded on…

view full answer...

Answer 3

The 26" Long 4-Leaf Double-Eye Spring for 4,000-lb Trailer Axles #e22YR will work great as a replacement for your Dexter Axle Leaf Spring 072-022-00. This is rated for a slightly higher weight rating but it isn't too much higher so you…

view full answer...

Answer 4

Based on previous information we have for your UFP HD-1377-10 hub it uses the following components. I do recommend pulling one of your hubs to verify that the replacements listed below match your current parts. Inner Bearing #L68149 (Inner diameter…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 11

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Replacement Parts Available for etrailer 3,500 lb Trailer Axle

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching