Tool Needed To Secure DC Output Wires In A Progressive Dynamics PD9280

Question

Question:

What tool do I use to get the Positive and Negative wires in or out of the Inteli Power PD9280? Thanks

asked by: Jesse L

1

Helpful Expert Reply:

The Progressive Dynamics Inteli-Power RV Converter and Smart Battery Charger # PD9280A DC terminals use a 5/32” hex bit # PT79VV to secure the wire. You'll want to ensure that you don't exceed 50 in-lbs. torque on the output terminals when you're tightening them down.

expert reply by: Kevin C

1

PD9280A DC Output Terminals
(click to enlarge)

Answer 1

The amperage is going to be the more important factor for a converter like the #PD9280A. We calculate energy for batteries in amp hours, so the higher amount of amps you can recharge in and hour the faster the battery will charge. That being said,…

view full answer...

Answer 2

I recommend you start by just replacing the fuses. If that fixes the problem, you are all set. If not, I recommend replacing the power converter with a new unit. I can recommend a similar model to replace your existing converter if you can find the…

view full answer...

Answer 3

Yes we can. The correct replacement converter would be the part #PD9270 to replace your WF9865.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

If you are just looking for a new converter, the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers part #PD4635V will be a direct upgrade for the Magnetek Converter Series 6300 Model 6332 that you have now.

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the two models that you were researching is that the #PD9160A is designed for use with lead acid batteries and the #PD9160ALV is designed for use with lithium batteries. Choosing the incorrect battery profile can lead to issues…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The Progressive Dynamics Replacement Section #PD4655V does have a jumper to change the charging profile to lithium compatible. You'll simply need to move the black jumper over from the WIZ side to the LI side.

view full answer...

Answer 11

Great question Larry, so the current version of the Progressive Dynamics converter #PD4655V does support lithium batteries as-is. At one point it did not but since lithium batteries have become more popular Progressive Dynamics decided to make this…

view full answer...

Answer 12

Since the part #PD4655V has come out and has ability to switch between lithium and lead acid batteries the part PD4655LIV was discontinued. At one point there were separate parts for lithium and lead acid batteries but since the current one can do…

view full answer...

Tool Needed To Secure DC Output Wires In A Progressive Dynamics PD9280

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching