Bearing Kit For Dexter 3,500 lb Axles on 2020 Airstream

Question

Question:

Looking for replacement wheel bearing kit for 2020 Airstream Baseccamp X with 3500#, Nev-R-Adjust, Dexter Axle, Airstream part #410980-19. And, what is the difference between your value and premium kits? Thanks!

asked by: Jim M

0

Expert Reply:

The correct bearing kit for your Dexter 3,500 lb axle with Nev-R-Adjust brakes for your Airstream is the following:

- Hub Bearing Kit # BK2-100

As for premium kits, I'm not quite sure what you are referencing, but the bearings we offer will work exactly the same as any other.

expert reply by: Kyle S

0

Answer 1

Since your hub/drum is 12 inch by 2 inch the correct self adjusting brake assemblies would actually be the part #AKEBRK-7-SA. Then for the correct hub/drum you'd want the part #AKHD-655-6-EZ-K. The drum portion of a hub doesn't affect the…

view full answer...

Answer 2

Yes, the 2020 Airstream Globetrotter 27 uses Dexter Torflex #11 Axles so the Torflex Lift Kit part #K71-724-02 will work.

view full answer...

Answer 3

While I don't know the exact grease seals used on your 2016 Airstream 16’ Bambi, I have narrowed it down to 2 options and it all just depends on what spindle you have. If you have a BT8 spindle with the #L44643 inner and out bearings then you…

view full answer...

Answer 4

You can verify that the 10-19 grease seal included in Bearing Kit #BK2-100 is the correct one for your spindles by taking two measurements. First you want to measure the rear hub bore where the seal is inserted. The seal's outer diameter needs to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 11

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...

Answer 12

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Bearing Kit For Dexter 3,500 lb Axles on 2020 Airstream

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching