Are There Replacement Parts For Fulton XLT 1500 Jack # F26ZR

Question

Question:

Can I get a complete wheel assembly for a Fulton 1500 XLT trailer jack. Thank you

asked by: Jeff S

0

Expert Reply:

Though we do not carry a complete replacement wheel assembly for the Fulton XLT Bolt-Thru Swivel Trailer Jack # F26ZR, you will have to purchase the entire jack again.

If you have any further questions please feel free to reach back out to me anytime and I would be more than happy to further assist.

expert reply by: Noah E

0

Answer 1

Yes, since your current Fulton jack is a bolt-thru style, you can use the Fulton XLT Bolt-Thru Swivel Trailer Jack #F26ZR with your current welded on bracket. You just need to remove the jack from the included bolt-on bracket and mount it to your…

view full answer...

Answer 2

If you used a 1.5 inch spacer to make your 1.5 inch wide frame 3 inches wide you could use the Fulton XLT Bolt-Thru Swivel Trailer Jack #F26ZR.

view full answer...

Answer 3

If you are not wanting a bolt-on jack such as the Fulton XLT Bolt-Thru Swivel Trailer Jack, #F26ZR we have the Fulton F2 Adjustable A-Frame Jack, #F1413250334. The F2 Series jack is specially designed for use with Fulton's F2 A-frame coupler.…

view full answer...

Answer 4

The Fulton XLT Bolt-Thru Swivel Trailer Jack #F26ZR comes with brackets that would allow you to attach to the trailer frame that bolt around the frame but if you wanted to drill holes in the trailer frame and attach it through the frame you could…

view full answer...

Answer 5

In regards to the Fulton XLT Bolt-Thru Swivel Trailer Jack part #F26ZR, the distance from the center of the mounting bracket to the top of the jack tube cap is 13.4". I have attached a photo below as well to show this. I spoke to Fulton and…

view full answer...

Answer 6

The mounting plate for the Fulton XLT Bolt-Thru Swivel Trailer Jack #F26ZR has the following dimensions. I have included an image to show the measuring points. The holes are spread 5-1/2" wide with the vertical holes separated 1" on the…

view full answer...

Answer 7

I went ahead and checked out your Fulton XLT Bolt-Thru Swivel Trailer Jack #F26ZR, and the Fulton F2 Swing-Up Trailer Jack, and you actually won't be able to use this mounting bracket with your XLT jack due to the fact that the plate for the F2…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Are There Replacement Parts For Fulton XLT 1500 Jack # F26ZR

Product Page this Question was Asked From

Continue Researching