How Does Replacement Mounting Bracket for Yakima SlimShady Roll-Out Awning Install

Question

Question:

How does this part attach to the bracket clamp assembly? I see that it slides on but there’s no bolt to keep it in place

asked by: Michael I

0

Expert Reply:

I attached a picture that I got from Yakima that shows how the install bracket for the SlimShady part # 8880736 installs.

expert reply by: Jameson C

0

Clamp Mounting Instructions
(click to enlarge)

Answer 1

The vertical spacing you're asking for is 1-1/2" for the Replacement Mounting Bracket for Yakima SlimShady Roll-Out Awning #8880736 (see attached). I confirmed this with my contact at Yakima.

view full answer...

Answer 2

Yes, you can use the Replacement Clamp Assembly #8880737 and Replacement Mounting Bracket #8880736 for the Yakima SlimShady will work for your Roam awning. We actually have a review from a customer who purchased this combination for the same exact…

view full answer...

Answer 3

The Yakima SlimShady Roll-Out Awning - Roof Rack Mount - Clamp On - 6-1/2 foot x 6-1/2 foot #Y36VR will fit without modification to your factory installed cross-bars on your 2016 Toyota Highlander. The awning requires the crossbars have a minumum…

view full answer...

Answer 4

To install the replacement clamp assembly #8880737 and bracket #8880736 on the Yakima SlimShady Awning #Y36VR, there are two t-bolts that are inserted into the upper channel of each side of the SlimShady rail. You would then place the clamp onto the…

view full answer...

Answer 5

Since we don't sell ARB products, I'm unable to tell you with any certainty whether or not you can make this work; Yakima also doesn't test their products with other manufacturers. If you're trying to use the T-slot mounting channel…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

How Does Replacement Mounting Bracket for Yakima SlimShady Roll-Out Awning Install

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching