Can SeeLeveL RV Holding Tank Monitoring System Be Installed on a Fiberglass Holding Tank

Question

Question:

Will the sensors work on a fiberglass holding tank? If not, can you recommend a sensor that does?

asked by: Mark S

1

Helpful Expert Reply:

Yes, the SeeLeveL RV Holding Tank Monitoring System # SE39VR will work with a fiberglass holding tank. If you check out the linked installation video you'll see one of our installers putting this on a fiberglass tank.

expert reply by: Jon G

1

Answer 1

Yes, the Seelevel sensors like the part #SE78VR can be used on external mounted tanks exposed to water and roads like you asked about.

view full answer...

Answer 2

Yes we do carry the SeeLevel 709-2P with our part number #SE94VR. This is just the monitor you are looking for. The part #SE49VR that you mentioned includes the monitor but also sensors.

view full answer...

Answer 3

The SeeLeveL RV Holding Tank Monitoring System, #SE39VR operates from a 12 VDC power source. The installation consists of mounting the display inside the RV, cutting and fastening the senders to the sides of the holding tanks, connecting wiring,…

view full answer...

Answer 4

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 5

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 6

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 7

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 8

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 9

A 4-way trailer connector will have four functions which means it will also have four wires for the exception of wishbone harnesses. These four functions are ground, tail light, right turn, and left turn. The ground function will usually be…

view full answer...

Answer 10

It really just depends on what the wires are for. Most likely you have several ground wires among the 8 as well as a couple running light circuits in there as well. You just have to run all of the wires to the correct circuits. The 4-way wiring of…

view full answer...

Answer 11

Since the discontinued MaxxAir 4700k model fits a standard 14 x 14 RV vent opening, I recommend the MaxxFan Plus Roof Vent w/ 12V Fan - 10 Speed #MA00-04500K. The MaxxFan Plus comes with a thermostat and a remote for easy temperature customization.…

view full answer...

Answer 12

Hey Steve it looks like the oven you're referring to has been marked obsolete by Furrion so there are no replacement parts for it unfortunately. We do have the Replacement Oven Door for 21" Furrion 2-in-1 Range Oven #FR66NR which fits the…

view full answer...