Option For 60 Inch Trailer AxleSince it appears nobody makes hubs for my

Question

Question:

Okay, Since it appears nobody makes hubs for my trailer, lets consider the axle replacement. The one recommended is too large. I believe I need one with a total length of 60 inches or close to it. The spring centers measure 40-1/2 inches, but I think I could slip them out an inch or so to make a fit. Got anything for that? Thanks

asked by: Phil P

0

Expert Reply:

We do have axles with 60 inch hub face to hub face measurements. This is a 2,000 lb axle, though the spring centers measure 48 inches. What you can do though is have new springs welded on at the location you need with Spring Seat # TRSS175.

This axle is the Trailer Idler Axle Beam with Easy Grease Spindles - 60" Long - 2,000 lbs # e48GR.

Then for the hubs, the right one for you will depend on if you need a hub with a 4 on 4" bolt pattern or 5 on 4-1/2" bolt pattern, as well as your wheel size. If you aren't sure what your bolt pattern is, I have added a link below to a help article which explains how to measure for it.

- 4 on 4" Bolt Pattern / 8" to 14" Wheels: Easy Grease Trailer Idler Hub # AKIHUB-440-2-EZ-2K

- 5 on 4-1/2" Bolt Pattern / 10" to 12" Wheels: Easy Grease Trailer Idler Hub # AKIHUB-545-2-EZ-2K

- 5 on 4-1/2" Bolt Pattern / 13" to 15" Wheels: Easy Grease Trailer Idler Hub # AKIHUB-545-2-LFEZ-2K

expert reply by: Kyle S

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 3

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 6

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 7

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Answer 8

There really isn't a particular maximum trailer weight that is used to determine when brakes need to be added to both axles of a tandem axle setup. While I do still recommend checking your local laws, I am also not aware of any general laws that…

view full answer...

Answer 9

Thanks for the information on your trailer. For your axle with brakes I recommend the Trailer Hub and Drum Assembly - 5,200-lb and 6,000-lb E-Z Lube Axles - 12" - 6 on 5-1/2 #AKHD-655-6-EZ-K if you have the spindles with the integrated grease…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

To determine if there are compatible hubs and associated bearings to replace your current hubs to a more standard size you will have to take several precise measurements on the spindle of your axle. It is recommended to use a set of dial calipers to…

view full answer...

Option For 60 Inch Trailer AxleSince it appears nobody makes hubs for my

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching