Can MORryde 5th Wheel Cross Brace Landing Gear Stabilizer Work with SnapPads

Question

Question:

Need to confirm that the MORryde X-Brace works with Snap Pads installed on the jack foot.

asked by: Bradley J

1

Helpful Expert Reply:

SnapPads would not interfere with the MORryde 5th Wheel Cross Brace Landing Gear Stabilizer # MR72AR at all so the two would easily work well together.

expert reply by: Jameson C

1

Answer 1

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 2

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 3

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 4

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 5

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 6

The Replacement Amber Lens for MC32AB Trailer Lights #A32AB is a direct replacement for the SAE A P2 DOT 14 and would be what you'd need.

view full answer...

Answer 7

The Bargman 7-Way, RV-Style Connector #WG54006-043 referenced in your question uses the standard RV-style pin locations for its 7-Way connector. I have attached a diagram of these locations and their functions for you to check out. Wire colors will…

view full answer...

Answer 8

The best modern day size replacement option we have for a 6.00-16 is a 235/80-16 which measures 30-7/8" diameter x 9-3/8" wide. For this, I recommend the Kenda Karrier ST235/80R16 Radial Trailer Tire with 16" Black Mod Wheel part…

view full answer...

Answer 9

The 18.5x8.5-8 is actually an old tire size that is not used much anymore. The closest metric size to your existing tire would be 215/60-8. Your wheel most likely has a 5-on 4-1/4 inch bolt pattern (see link), you will want to make sure that the bolt…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 12

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Can MORryde 5th Wheel Cross Brace Landing Gear Stabilizer Work with SnapPads

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching