What Do the Ends of the Gen-Y Hitch Aluminum Loading Ramp Set 325-GH-R84 Look Like

Question

Question:

Which photos accurately depicts the design of the bottom ends of the ramps?

asked by: David

0

Expert Reply:

At one point the ends of the Gen-Y Ramps like the part # 325-GH-R84 were different but at this time the ends of the ramp look like what you see in the attached photo.

expert reply by: Jameson C

0

Ramp Design
(click to enlarge)

Answer 1

For a 12k winch I recommend the Bulldog Winch Trailer Winch #BDW10039. Bulldog is a well-known name in the winch community and this specific model comes with a wireless remote that you can use to easily activate the winch from anywhere within a…

view full answer...

Answer 2

The plate that the winch mounts to is 1/4 inch thick. This mount has 2 sets of four (eight) holes, centered on the cable opening, in a rectangular pattern for mounting the winch to the plate and the measurements are 6-1/2 by 4-1/2 inches on center…

view full answer...

Answer 3

The rungs on the Stallion Loading Ramp Set #288-07489 that you referenced have 3" gaps between them as you can see in the attached photo. My contact at Stallion confirmed this. If the spacing is too much for you to use and the 3,000 lbs weight…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 7

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 8

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 9

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...