Replacement Axle Options For Dexter TORFLEX Torsion Axles

Question

Question:

I am looking for a replacement or equivalent to the following product. Dexter Torflex rubber torsion axle 059-558-00 Rev C

asked by: Ray O

0

Expert Reply:

While we do not carry Dexter TORFLEX axle we do have the Timbren Axle-Less options. Here is a list of some of the basic options without hubs.

Timbren Axle-Less Trailer Suspension System - Spindle Only - Regular Tires - 1,200 lbs # ASR1200S02
Timbren Axle-Less Trailer Suspension System - Spindle Only - Regular Tires - 2,000 lbs # ASR2000S01
Timbren Axle-Less Trailer Suspension System - Straight Spindle Only - 3,500 lbs # ASR3500S05

These use Timbren's AEON progressive-rate main springs to absorb road shock and support trailer's load. As I was unable to determine exactly what capacity your axle is if you can provide me with more details on what the axle goes on I can help you determine the best replacement option.

expert reply by: Bud M

0

Answer 1

To replace the hubs on your trailer, I will need you to pull one of your hubs and look for the inner and outer bearing. On the face of each of these bearings, there is a number. That number will help me get you the correct hubs for your trailer. If…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 4

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 7

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 10

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...