Availability of Replacement Hardware for Thule Fit Kit

Question

Question:

Ive been trying to find fit kit bolts only. I have the 3131 but cant find the fit kit BOLTS only. I lost mines

asked by: Steve

0

Expert Reply:

According to Thule, fit kits like the # THKIT3131 are pre-packaged in Sweden and shipped to the US as a complete unit. Unfortunately, this means that the only option for bolts and other hardware is to purchase the complete fit kit since Thule does not offer them separately.

expert reply by: Robin H

0

Answer 1

We do have the brackets, bolts, and nuts needed to attach your Thule Hullavator 897XT to the round bars. What you need are the following parts: - Replacement Underbar Bracket #TH8535860 - Replacement M6 x 22 Carriage Bolt #915-0622-54 - Replacement…

view full answer...

Answer 2

Since we have started carrying the Yakima Rack and Roll trailer #Y08107 I have not heard any complaints regarding the wheel bearings failing and only a few instances where people wanted to replace the wheel assembly. If you need to replace your…

view full answer...

Answer 3

There is no problem with storing the Yakima Rack and Roll Trailer - 78" #Y08107 outside as it is made out of aluminum so it is corrosion resistant. A cover is not required, and at this time Yakima does not make a cover for the trailer. If…

view full answer...

Answer 4

I spoke to my contact at Yakima and she informed me that since your kayaks will be behind your vehicle and not on top it is not as important to have the kayaks strapped down when used on the Yakima Rack and Roll Trailer #Y08106. She did recommend…

view full answer...

Answer 5

The only roof mount bike rack that will work for you is the Inno Tire Hold II Roof Bike Rack #INA389 as it has a 50 lb weight capacity and will fit the crossbars on your Yakima Rack and Roll trailer, like part #Y08107. This is a wheel mount bike…

view full answer...

Answer 6

The Yakima Rack and Roll Trailer #Y08107 can be stored upright. The trailer is 22" tall, so if stored upright the depth will be around 22". Give or take a little because it does sit at a slight angle when upright. It can be unhooked…

view full answer...

Answer 7

No. 78" Long Yakima HD bars #Y01159 cannot be mounted on the Yakima Rack and Roll Trailer #Y08107. The Rack and Roll trailer is only designed to be used with round crossbars. If you're looking for a kayak carrier that has a higher…

view full answer...

Answer 8

I do have an option for you which is to install load stops onto the crossbars to stop loads from shifting, the LoadStop Brackets for Yakima Round Crossbars part #Y05000. That said, there isn't an option to replace round crossbars with…

view full answer...

Answer 9

While there isn't a life expectancy, per se, of the shocks on the Yakima Rack and Roll Trailer - 66" #Y08106 and 78" #Y08107, upgrading to the HD shocks is absolutely a good idea if your gear weighs around 200 llbs and…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 12

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Availability of Replacement Hardware for Thule Fit Kit

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching