Stabilizer Jacks For a 1959 Kencraft Vintage Trailer

Question

Question:

should these work for my vintage trailer?

asked by: Darcy M

0

Expert Reply:

The Stabilizer Jacks # TJ01RT-HD are a more universal design and should work with your 1959 Kencraft vintage trailer.

The Stabilizer Jacks # TJ01RT-HD have a lift capacity of 650 lbs. per jack, a support capacity of 1,000 lbs. per jack and can be bolted or welded on. They have a retracted height of 11-1/2" and an extended height of 18".

The Mounting plate dimensions are:
- 4" long x 1-7/8" wide
- 3" From center of hole to center of hole
- 7/16" Diameter holes

expert reply by: Scott S

0

Answer 1

There many possible ways to mount a stabilizer jack such as the #TJ01RT-HD you looked at. Mounting them in the orientation shown the diagram would tend to work a bit better to stabilize the trailer against side to side movement, while having the…

view full answer...

Answer 2

I went out to the warehouse and found that the distance from the center of the jack to the furthest part of the adjustment pin on the Ultimate Trailer Jack #322-RDJ-2K when it is pulled out is 5-3/8". If you have this much room from the center…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 5

The Ark Drop Down Corner RV Stabilizer Jacks #ARK94FR are able to lock into place at 30 and 60 degrees as stabilizers. They also have the 90 degree position where it is rated for 1,929 lbs and then the stored position.

view full answer...

Answer 6

It does; the valve stem is indeed included with the Karrier ST205/75R15 Radial Trailer Tire with 15" Aluminum Wheel - 5 on 4-1/2 - Load Range C #KE27JR.

view full answer...

Answer 7

The weld-on mounting bracket for the ARK #AR94FR Drop Down Corner RV Stabilizer Jacks measures 4-5/8 x 2-7/8 inches. The bracket has holes for the hardware that attaches the jack to the brackets. The holes are 2-7/8 inches apart on center. I've…

view full answer...

Answer 8

Since the tongue of your trailer flares out you could just cut a piece of wood to match the angle of the flare to square up the tongue and then clamp-on the etrailer Round/Wheeled Swivel Jack #e79CR. If the trailer stays outside a majority of the…

view full answer...

Answer 9

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

Answer 10

While we don't carry that exact part number we do have a replacement hub/drum that would work just as well with the part #AKHD-655-6-EZ-K. This is a 6k hub/drum that fits the spindles of the Timbren Axle Less Kit part #ASR1THDS03.

view full answer...

Answer 11

You have a good eye as the black tubing sections are plastic for the Camco Gen-Turi RV Generator Exhaust System #CAM44461. It's just the curved pipe section that is made out of stainless steel.

view full answer...

Stabilizer Jacks For a 1959 Kencraft Vintage Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching