Dimensions of Progressive Dynamics Pure Sine Wave Inverter w/ Transfer Switch # PD94FR

Question

Question:

I didn’t see anything on the converter dimensions as I will be replacing the remote to the WF-600 and I want to make sure I will have room to mount it.

asked by: Scott S

0

Expert Reply:

The dimensions of the Progressive Dynamics Pure Sine Wave Inverter w/ Transfer Switch # PD94FR that you referenced are 11-1/4" long front to back x 6-5/8" wide from left to right x 4" tall.

expert reply by: Jameson C

0

Answer 1

Thanks for the picture! I couldn't get all the information I needed off of the tag but our best option to replace the axle on your Keystone Montana is the Dexter Trailer Axle w/ Electric Brakes item #8327826-EB. This axle has a 6,000 lbs…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures…

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 7

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 8

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 9

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 10

Generally speaking bearing grease has so little water in it that significant expansion due to freezing temperatures is unlikely. Higher operating temperatures within the hubs while underway would potentially thin the grease but again not cause much…

view full answer...

Answer 11

I have attached a chart you can check out that describes the torque needed per wheel size, wheel stud size and material. For an 8-inch wheel with a 1/2-inch wheel stud the torque is 75 to 86 ft-lbs. For a 15 inch steel wheel with 1/2 inch wheel studs…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Dimensions of Progressive Dynamics Pure Sine Wave Inverter w/ Transfer Switch # PD94FR

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching