Bearing Kit for Lippert 3,700 lb Trailer Axle

Question

Question:

I have a Lippert 3,700 lb axle that I am looking for the correct bearings and grease seal for. Can you help me out. I do have a picture of the product sticker but could not find a way to attach it to this inquiry.

asked by: Sam R

0

Expert Reply:

The 3,500 lb and 3,700 lb axles use the same bearings and seals. Therefore, you can use the Bearing Kit for #84 Spindle part # BK2-100 with your Lippert 3,700 lb axle.

expert reply by: Jameson C

0

Answer 1

The 168255TC oil seal is designed for use on for oil bath hubs, but they can be used on grease hubs. They basically just provide a better seal to hold oil in; they will still work for grease. The springs on your oil seals are required to function…

view full answer...

Answer 2

We do have a compatible grease seal for your 168255TC oil seal, however, we do not carry rubber coated seals in this size. The 168255TC oil seal was designed to work with oil bath hubs on a 3,500 lb axle. For the most part, axle manufacturers have…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 7

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...

Answer 8

The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a…

view full answer...

Answer 9

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

On Dexter 12" Nev-R-Adjust Electric Brake Assembly #23-458 the shoe pad thickness is 3/16 of an inch. Dexter says that you should replace the shoes if the material gets down to 1/16 of an inch thick or less.

view full answer...

Answer 12

The inner diameters of the LM67048 and 15123 both are the same (1.250 inches). That means that a hub with either bearing in the outer bearing would fit your spindle. The part #AKHD-655-6-EZ-K would fit your axle.

view full answer...

Bearing Kit for Lippert 3,700 lb Trailer Axle

Product Page this Question was Asked From

Continue Researching