Replacement Battery For Bright Way Push-to-Test Trailer Breakaway Kit # 3802346

Question

Question:

Is it possible to replace just the battery, or do I have to replace the entire unit. The charge light comes on, but battery is dead.

asked by: Michael

0

Expert Reply:

Yes, you can replace just the Battery # 3801250 on your Bright Way Push-to-Test Trailer Breakaway Kit # 3802346.

expert reply by: Bud M

0

Answer 1

Based on your dimensions it sounds like you need a box for a trailer breakaway battery. All of the replacement breakaway battery boxes we offer can be seen on the link provided. For example, the inside of part #TK2018 measures 5-3/8 L 3-1/16 W…

view full answer...

Answer 2

Easily the highest quality trailer breakaway battery with a charge and indicator is from Tekonsha, and is the following part number: - Tekonsha Push-To-Test Trailer Breakaway Kit with Built-In Battery Charger #50-85-313 Tekonsha has a deserved…

view full answer...

Answer 3

The front cover of the Bright Way Push-to-Test Trailer Breakaway Kit #3802346 is supposed to swing out like you mentioned. I attached pictures that show the door open. I'd be willing to bet the hinge on the left side of the door isn't fully…

view full answer...

Answer 4

Thanks for the picture! I have a solution for you but you aren't going to be able replace just the box on your trailer. You will want to use the Bright Way Push-to-Test Trailer Breakaway Kit with 1-Amp Charger and 5 Ah Battery item #3802346. This…

view full answer...

Answer 5

The small breakaway battery shouldn't be going dead unless the breakaway switch is being pulled, there's a short in the system somewhere or the system has been incorrectly wired. The battery should be receiving a maintenance charge from the…

view full answer...

Answer 6

It is definitely a good idea to have a trickle charger hooked up to your trailer battery in the colder months when it isn't being used. For this I recommend the CTEK MULTI US 7002 #CTEK56353. This designed for use with 12 volt batteries and…

view full answer...

Answer 7

I think the best way to test the battery charger on your breakaway kit is to apply 12V power to the wire that connects to the 12V power wire on your trailer and then test the other wire on the module to see if there is power coming through. If power…

view full answer...

Answer 8

The Bright Way Push-to-Test Trailer Breakaway Kit w/ 12V, 5-Amp-Hr Battery and 1-Amp Charger - Side Load Item #3802346 needs to be mounted with the words/writing facing out as in the video. It is a side load so the terminals on the battery are at the…

view full answer...

Answer 9

The Bright Way Trailer Brakeaway Kit #3802308 has a built in 1-AMP charger. So when your truck is connected it will be charging. There should be no draw going out while the trailer is disconnected so it should be ready to rip whenever you're…

view full answer...

Answer 10

The Bright Way Push-to-Test Trailer Breakaway Kit #3802346 was designed to attach to the outside of a trailer frame like you asked about so it would work well for you. It is weather proof so that it would do fine as long as you didn't submerge it…

view full answer...

Answer 11

The Bright Way Push-to-Test Trailer Breakaway Kit #3802346 typically requires drilling into the trailer frame in order to install it. Unfortunately, this breakaway system does not have a weld-on trailer frame mounting plate option. For a breakaway…

view full answer...

Answer 12

Although the Tekonsha Prodigy P3 #90195 and Primus IQ #TK90160 electric brake controllers are very similar they do have some key differences as well. For one the P3 is designed to work with electric and electric over hydraulic brake systems. The…

view full answer...

Replacement Battery For Bright Way Push-to-Test Trailer Breakaway Kit # 3802346

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching