Dexter Brake # K23-532-00 Bolt Pattern Measurements

Question

Question:

Please verify 4 bolt pattern is 3 3/4 inch apart on center. Thank you

asked by: Chi V

0

Expert Reply:

Yes, The Dexter Brake # K23-532-00 4 bolt pattern is 3-3/4 inches apart on center.

expert reply by: Noah E

0

Brake Measurements
(click to enlarge)

Answer 1

Based on your picture and my research it appears that you may have a 6 bolt pattern mounting flange but will only use 5 bolts to attach. With that being said, a 12 1/4" diameter, 3 1/2" wide hydraulic brake assembly replacement…

view full answer...

Answer 2

The Dexter Electric Trailer Brake Kit #K23-532-533-00 is for 8,000 lb axles and has a 4-bolt pattern that is 3-7/16" across and 3-5/8" vertically. They would mount to a 4-bolt brake mounting flange such as Trailer Brake Mounting…

view full answer...

Answer 3

I checked the sizes for you, and both of these electric brakes are in fact 12" diameter x 3-3/8" wide: - Left Hand Side: Dexter Electric Trailer Brake Assembly #K23-532-00 - Right Hand Side: Dexter Electric Trailer Brake Assembly…

view full answer...

Answer 4

The four bolt brake mounting flange for 8,000 lb trailer axles is going to be more or less an industry standard. This industry standard is 3-5/8" across left to right on center and 3-7/16" top to bottom on center. This could very well vary…

view full answer...

Answer 5

The Dexter Electric Trailer Brake Assembly #K23-532-00 has a square mounting pattern with the bolt holes centers being 3-3/4" on center. This particular assembly is for the drivers side of the 8,000-lb AL-KO / Hayes axle. We also have the…

view full answer...

Answer 6

The green wire from the controller attaches to the cold side of the brake stoplight switch, the white ground wire attaches to the negative battery terminal, the red wire supplies 12-volt power to the controller, and attaches to the positive battery…

view full answer...

Answer 7

Like you said we have 12-1/4 x 3-3/8 inch brakes but no 12 x 3-3/8 inch brakes. When measuring though measure the inside diameter of the drum and not the diameter of the brakes. I have included a picture showing what I mean. If you measure the drum…

view full answer...

Answer 8

You can check the condition of your hub's races by carefully removing all bearing grease with a rag to expose the actual surface of the races. When they are completely free of grease, etc., inspect them for any signs of scoring (very slight…

view full answer...

Answer 9

Based on what information I could find about AL-KO 8490 hub and drums, it is rated for 3,500 pound axles, has a 5 on 4-1/2 bolt pattern, and is a 10 by 2-1/4 inch drum. If this is the case, we have several options for you. I have attached a link to…

view full answer...

Answer 10

According to my research, AL-KO 8490 references an AL-KO hub for 3,500 lb axles with a 10 x 2-1/4" drum and a 5 on 4-1/2" bolt pattern. For a drum assembly that will work with these hubs I recommend taking a look at the Electric Trailer…

view full answer...

Answer 11

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 12

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Dexter Brake # K23-532-00 Bolt Pattern Measurements

Product Page this Question was Asked From

Continue Researching