Replacement Ramp Door Handle for a Horton Enclosed Trailer

Question

Question:

I have a Horton Trailer model H612TA. I need to replace the handle on the back ramp that s down. I cant find it on your site. Can you help?

asked by: Scott

0

Expert Reply:

After doing some research on Horton trailers, it looks like most of their enclosed trailers use cam-door style lock like part # 383200. If you just need a replacement handle, I recommend using part # 158-100. This handle measures 12-5/8 inches long and works with the cam-door style locks.

expert reply by: John H

0

Answer 1

The hinge you referenced part #PLR2212-AS would replace what you have now on your horse trailer and the holes would line up. It looks like for your window you'd need a piano hinge that's about 2 feet long, but at this time we do not have any…

view full answer...

Answer 2

The T-Strap Hinge for Side and Rear Trailer Doors - 8" Long - Steel #PLR3408 will not be ideal for a 90 degree corner as you can see the purposeful bend at the hinge on the strap end of the hinge that would limit this. A better option for that…

view full answer...

Answer 3

We currently offer 3 different replacement strap hinges, #2008-8, #2512, and #2212, for cargo trailers. I have included a photo showing each of these with their measurements listed. I recommend comparing these measurements to the strap hinges on your…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...