Are Cable Zip Ties Required To Secure Curt Auxiliary LED Indicator Lights # C53201 To a Bike Rack?

Question

Question:

I recently got a set of your LED indicator lights for the back of my bike rack. They are a peel and stick strip aobut 7 in long both left and right. Will they stay stuck on for a long time or do I need to also use some zip ties to hold them in place long term?

asked by: George C

1

Helpful Expert Reply:

The 3M adhesive backing on the Curt Auxiliary LED Indicator Lights # C53201 is a very strong adhesive that will last for a long time. It is important to have a smooth clean surface to attach the lights, otherwise they may not stay attached. While you will not need Cable Ties # DW05727-25 to hold the lights themselves in place they should be used to secure the wiring and prevent it from getting caught on part of your bikes when loading and unloading,

expert reply by: Bud M

1

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

There are some subtle difference between the Kuat Piston Pro Bike Rack for 2 Bikes #KU76ZR and the Kuat Piston Pro X Bike Rack for 2 Bikes #KU98VR. Overall the two racks are very similar, there are just some subtle differences/upgrades on the Piston…

view full answer...

Answer 5

Hey Dave, so the best option for carrying your carbon frame bike and e-bike is the Swagman Escapee part #S39SR with the ramp #S59SR . It has the capacity for carrying an e-bike, is rated for travel trailer use, only touches the bikes by the tires…

view full answer...

Answer 6

As long as the flat tow wiring is wired in before the 4-Way #C93ZV and you connect the power for the converter directly to the battery it will work. I have seen several use Magnetic Lights #TL21RK which they will wire in on the main harness to have…

view full answer...

Answer 7

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 8

When determine if you can fully open swing-out doors on your 2022 ProMaster 3500 with the Yakima EXO #Y34ZR, it really depends on how far your doors swing when in the open position. While the 90-degree swing has not been tested spcificially on a 2022…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

In order to use a hitch-mounted bike rack like the Swagman Original #S64152-2 that you were looking at while towing a vehicle, you will just need to add the Roadmaster Dual Hitch Receiver Adapter #RM-077-4. This adapter will slide into the 2 inch…

view full answer...

Are Cable Zip Ties Required To Secure Curt Auxiliary LED Indicator Lights # C53201 To a Bike Rack?

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching