How Should Ignik Backside Heated Seat Pad # GN34FR be Cleaned

Question

Question:

How do they recommend cleaning the cover?

asked by: Shawn M

0

Expert Reply:

A wet rag should easily clean the Ignik Backside Heated Seat Pad # GN34FR that you referenced. To be on cautious side you should have it unplugged and let it dry before plugging back in.

expert reply by: Jameson C

0

Answer 1

Depending on the diameter of your existing bushings the Roadmaster Polyurethane Bushing Kit for 1 5/8 inch diameter #RM-4139-127 may fit. We also offer a few other sizes to choose from. Rear 1 1/2 inch Diameter Bar: Roadmaster Polyurethane Bushing…

view full answer...

Answer 2

To replace/upgrade the bushings on the rear factory sway bar of your 2009 Class A Newmar Canyon Star RV you need one of the following Roadmaster kits based on the diameter of your factory sway bar: - 1-3/8" Diameter #RM-4139-300 - 1-1/2"…

view full answer...

Answer 3

Yes, since your 2019 Ford F-53 motorhome has a sway bar with a 1-3/8 inch diameter the bushing kit part #RM-4139-300 would fit.

view full answer...

Answer 4

In order to replace just the factory anti-sway bar bushings on a Ford F-53 Chassis you have a few options which will be based on the location of the anti-sway bar (front/rear) and the gross vehicle weight rating of the coach (15,700 lbs, 16,000 lbs…

view full answer...

Answer 5

I went out to the warehouse to inspect the Camco RV and Marine Septic Safe Toilet Tissue, #CAM40276, and the 2-ply version #CAM40274. I also spoke to a co-worker who has used these items and got her opinions. The single ply is soft but thin like any…

view full answer...

Answer 6

You will need to confirm if you have a 1-3/8" or 1-1/2" diameter rear sway bar on your 2003 Tiffin Allegro RV motorhome with the Ford F-53 chassis. The Roadmaster Polyurethane Bushing Kit #RM-4139-300 will upgrade you to polyurethane…

view full answer...

Answer 7

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 8

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 9

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 10

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

For a standard replacement equalizer for your Dexter 13-122 equalizers you'd want the #TREQE1 or for a cushioned version you'd want the part #K71-653-00 which comes with new shackles and bolts. For a kit that includes new bolts, bushings, and…

view full answer...

How Should Ignik Backside Heated Seat Pad # GN34FR be Cleaned

Product Page this Question was Asked From

Continue Researching