Could Wheel Dolly # PTW54013 be Used on Tandem Axle Pontoon Boat Trailer

Question

Question:

Will these work on a tandem axle pontoon trailer. Is there enough room for dollies to fit under each tire.?

asked by: Rowdy B

1

Helpful Expert Reply:

The Wheel Dolly # PTW54013 that you referenced would work for your tandem axle pontoon boat trailer but only if they trailer was under the weight capacity of the dollies. These are rated for 1,000 lbs per dolly so with a total of 4 of these your boat and trailer would need to weigh under 4,000 lbs.

expert reply by: Jameson C

1

Answer 1

We have the Wheel Dolly #PTW54013 which has a weight rating of 1,000 lbs per dolly so as long as the tongue of your boat trailer is supported these should do just fine.

view full answer...

Answer 2

Thanks for reaching out! The purpose of the Trailer Valet Trailer Wheel Dolly for Tandem Axle Trailers #TV56FR is to give you better maneuverability with a tandem axle trailer when utilizing a trailer dolly like the Trailer Valet XL #TVXL25. The…

view full answer...

Answer 3

The Performance Tool Moving Dollies #PTW54013 are used for moving a car, riding mower, trailer and many other items. They will definitely get your 2,500 pound car moved around. I have actually had people order two sets of these to get all 4 wheels…

view full answer...

Answer 4

Getting the trailer as close to level as you have should be just fine. If your only options are to be a tiny bit too high or a tiny bit too low I usually recommend going on the high side since most likely the suspension will compress slightly from…

view full answer...

Answer 5

The Trailer Valet XL part #TVXL25 that you referenced has been redesigned a couple times. One of the big changes they made was they went from inflated tires that had had the potential to lose air to solid tires that you never have to worry about. We…

view full answer...

Answer 6

I do have a solution for you but there are no front mount trailer hitches available for the 2003 Honda Element. What I recommend is a Trailer Valet XL trailer dolly such as #TVXL2 which has a 2 inch ball or #TVXL25 which has a 2-5/16 inch ball. These…

view full answer...

Answer 7

We do have a solution for you, though there is not a Gooseneck to 5th Wheel Trailer Coupler Adapter such as #KPG5-Q25-IP which has an offset. Since you are looking to use your gooseneck trailer and have a fifth wheel hitch I recommend checking out…

view full answer...

Answer 8

As your Kaufman 47' EZ 4 Trailer has 7,000lb axles you will need either the Hydrastar Kit #HSE7K-TR1 for 1/2" lug nuts or the Hydrastar Kit #HYD54FR for 9/16" lug nuts. Both kits include new hubs, calipers, bearings, brake lines, the…

view full answer...

Answer 9

Trailer Valet XL Trailer Dolly #TVXL25 will be able to move your trailer at the near 90 degree angle and up the incline of the driveway. The dolly has 2 gears and you will likely find that the low speed, 27 to 1 ratio will make it easier on you…

view full answer...

Answer 10

The Trailer Valet XL part #TVXL25 does work on a 10% incline or 5.7 degree angle as confirmed by Trailer Valet. However, the incline needs to be a gradual incline the Trailer Valet does not go over curbs or tall bumps in concrete. If your driveway…

view full answer...

Answer 11

The Trailer Valet XL Trailer Dolly with Chain Drive - 2-5/16" Hitch Ball - 1,000 lbs TW #TVXL25 and the other Trailer Valet products continue to use pneumatic tires. Solid tires would not give you the functionality and traction that you need…

view full answer...

Could Wheel Dolly # PTW54013 be Used on Tandem Axle Pontoon Boat Trailer

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching