What Size Guide Posts are the Replacement Mounting Hardware for CE Smith Roller Guide-On's For

Question

Question:

the square metal tubes for my guide posts are 1 1/2inch x 1 1/2inch do you have brackets for this size??

asked by: Michael A

0

Expert Reply:

The Replacement Mounting Hardware for CE Smith Roller-Style Guide-On part # CE11451-A is designed for use with 1-1/2" x 1-1/2" square tubing so it will work well with your guide-on posts.

expert reply by: Conner L

0

Answer 1

The CE Smith Replacement Hardware for Post-Style Guide-Ons #CE11452-A consists of 3-1/2 x 5-inch long U-bolts and brackets that measure 4-5/8 x 3-7/8 inches, according to my contact at CE Smith. This hardware kit is intended for replacing parts…

view full answer...

Answer 2

You will only need one set of the CE Smith Extra-Long U-Bolt Kit for Boat Trailer Guide-Ons - Pre-Galvanized Steel - 6" Tall, part #CE11416. Each side of the boat guide-on will take two u-bolts at the bracket. I have included a product…

view full answer...

Answer 3

Yes, the longer U-bolts of the #CE11416 will fit the #CE11451-A that you also referenced. The #CE11416 will give you U-bolts that are 1 inch longer than what's included with the #CE11451-A which are 5 inches long.

view full answer...

Answer 4

The dimensions of the Replacement Upright for CE Smith Bunk-Style Guide-Ons #CE27605PG are 39 inches tall by 23 inches long. The tube is 1-1/2 inches and the bend is a 90 degree angle. I've attached a picture for you as well.

view full answer...

Answer 5

We don't sell just the mounting bracket of the part #CE11452-A that you referenced but I added all of the dimensions to the picture you submitted.

view full answer...

Answer 6

I went out into our warehouse to grab a part #CE27608PG and found that the other dimension you are looking for is 17 inches.

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 10

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

What Size Guide Posts are the Replacement Mounting Hardware for CE Smith Roller Guide-On's For

Product Page this Question was Asked From

Continue Researching