Does Hole Need to Get Drilled in Bumper Cover to Install Hitch on 2022 Jeep Gladiator

Question

Question:

Cut the bumper out do the cap come with kit go over the bolt

asked by: Timothy B

0

Expert Reply:

When you install the Curt Hitch part # CU74FR on your 2022 Jeep Gladiator you will need to use a hole saw to drill a hole in the top of the bumper cover to access where the bolt threads. There isn't a cap available that comes with this kit or elsewhere that we are aware of.

expert reply by: Jameson C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

We offer the Curt #CU74FR and the Draw-Tite #DR64FR hitches for the 2022 Jeep Gladiator. The Curt #CU74FR mounts to predrilled holes in the rear crossmember/impact structure while the Draw-Tite #DR64FR attaches directly to the vehicle frame. The…

view full answer...

Answer 3

I checked with Curt and according to them, the Curt Trailer Hitch Receiver #CU74FR is a fit for all models of the 2020 Jeep Gladiator, including the Sport. You are correct that it will install partially through the ball mount hole in the bumper, as…

view full answer...

Answer 4

The Curt Trailer Hitch Receiver part #CU74FR is a fit for a 2021 Jeep Gladiator and an excellent option. If you don't want to drill through the bumper cover you can actually remove the bumper and install the hitch then re-install without…

view full answer...

Answer 5

I took a look at some pictures of a 2021 Jeep Gladiator with a trailer hitch installed from the factory. In all of those pictures, all you saw was the hitch receiver under the bumper. Given that information, the Curt Trailer Hitch Receiver #CU74FR is…

view full answer...

Answer 6

There are a couple of pretty big differences between the Draw-Tite Trailer Hitch Receiver #DR64FR and the Curt Trailer Hitch Receiver #CU74FR that fit your 2020 Jeep Gladiator, and I'll go over them so you can decide which trailer hitch is the…

view full answer...

Answer 7

I checked out the OEM hitch that fits your 2020 Jeep Gladiator and appearance-wise you'd only see the hitch opening hanging below the rear bumper. The Draw Tite part #DR64FR that you referenced instead would have the entire crosstube hanging…

view full answer...

Answer 8

Since the Redline Pre-Drilled Round Bumpers, part #D3-96, part #D2-96, and part #D4-96, are made of rubber I see no reason why you cannot drill out mounting holes so that they are custom to your hole patterns. If you will be using the full 96 inches…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Does Hole Need to Get Drilled in Bumper Cover to Install Hitch on 2022 Jeep Gladiator

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching