Replacement Wheel Stud for Easy Grease Trailer Hub and Drum Assembly for 5.2K & 6K Axles

Question

Question:

what size wheel stud is used with this hub? I cant seem to find replacements that are 1-1/4 inch long on your website, can you point me in the right direction thanks

asked by: JuniorV

0

Expert Reply:

The Easy Grease Trailer Hub and Drum Assembly # AKHD-655-6-EZ-K does use the 1/2" diameter x 1-1/4" long wheel studs and while we don't have any that match those specs exactly, the closest one we have is the Replacement Trailer Hub Wheel Stud # 165981 which is just 1/4" longer than the studs you have on the hub and drum assembly so it will work out just fine if you aren't able to source some locally.

expert reply by: Jon G

0

Answer 1

The standard replacement drive-in wheel stud for a 3,500 lb hub/drum like what you have on your Lippert 3,500 axle is the part #7-122 which is the correct thread size and length.

view full answer...

Answer 2

I wasn't able to find your specific part number hub but if you have a 5,200 lb hub with a 6 on 5-1/2 inch bolt pattern you are going to need a 1/2 inch drive in stud. If your existing drive in studs are 1-13/16 inches long (measurement B in…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Hey Jeremy, Typically with boat trailers the manufacturer will install hydraulic surge brakes because you don't have to worry about the water damaging wires like you would with electric brakes. That being said, if you use a heat shrink butt…

view full answer...

Answer 5

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 6

I'd be happy to help you out, John! To replace the brakes on your 5th wheel trailer you need the etrailer Electric Trailer Brakes #AKEBRK-7-SA which come with a self-adjusting feature so once you initially set them up you won't have to adjust…

view full answer...

Answer 7

Thanks for the information on your trailer. For your axle with brakes I recommend the Trailer Hub and Drum Assembly - 5,200-lb and 6,000-lb E-Z Lube Axles - 12" - 6 on 5-1/2 #AKHD-655-6-EZ-K if you have the spindles with the integrated grease…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 10

Hello Brian, we do offer some parts that will work for your application and will be very similar to the BPH1206EPR kit that you mentioned. Like you said, the 12 x 2-1/2 drums are pretty uncommon, so I would have to recommend going instead with the…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Replacement Wheel Stud for Easy Grease Trailer Hub and Drum Assembly for 5.2K & 6K Axles

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching