Are There Tools Involved to Install Titan Tire Chains TC2228CAM

Question

Question:

I have a 2011 ram 1500 with 265/70R17 Blizzaks. I am looking at purchasing yout tire chains TC2228CAM. Will I need a special tool/s to install them?

asked by: Jack I

0

Expert Reply:

The Titan tire chains part # TC2228CAM that you referenced do fit your tire size of 265/70R17 and do not require any additional tools to install.

I attached an install video for these for you to check out to show you what all is involved to install them.

expert reply by: Jameson C

0

Answer 1

I'd recommend removing the extra links as that will be safer than trying to secure them. This way you'd never have to worry about the links becoming unsecured and hitting something in your already tight clearances.

view full answer...

Answer 2

The Titan Chain Snow Tire Chains with Cams #TC2228CAM that fit your 2015 Toyota Tacoma with 265/70R16 tires can have some extra chain, and there are a couple of ways to deal with it. According to Titan, you can tie it off, or you can cut the extra…

view full answer...

Answer 3

I have the following installation instructions for Titan tire chains #TC2228CAM: Prior to use pre-fit tire chains to vehicle tires INSTALLATION INSTRUCTIONS Caution! Install tire chains in a safe place. Park vehicle away from traffic. Set parking…

view full answer...

Answer 4

I do show the Titan Chain Snow Tire Chains with Cams part #TC2228CAM as a fit for 265/75-16 tires. These are a great option for deep snow, mud, and even ice. The cams make adjusting for a tight fit on the tires nice and easy. The Titan Chain…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

I am far from an expert on snowmobiles but one would have to think such a large truck with the correct tires and chains would be able to make it through up to 2' of snow assuming you have clearance on the vehicle. In regards to the type of tire…

view full answer...

Answer 10

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 11

It will indeed work; I just checked with Lippert for you and was able to verify the correct toggle switch for your Lippert Power Stance Electric Trailer Jack #LC69VR (which is the 813748), is the following: - Replacement Extend/Retract Switch for…

view full answer...

Answer 12

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...