Replacement Tarp for Pace Edwards JackRabbit Tonneau Cover on 2007 Silverado Short Bed Truck

Question

Question:

I have a 2007 Silverado LTZ with 6.5 bed and trying to find a replace cover for my JACKRABBIT, Model TR2003, Serial# JC1105-0231

asked by: Arthur W

0

Expert Reply:

Thanks for reaching out!

It looks like you have the Pace Edwards JackRabbit Retractable Hard Tonneau Cover # 311-JRC0303 on your short bed 2007 Chevy Silverado Classic which means you need the Replacement Tarp # PE22KV.

expert reply by: Jon G

0

Pace Edwards JackRabbit ID Tag on 2007 Chevy Silverado Classic
(click to enlarge)

Answer 1

I reached out to my contact at Pace Edwards and the Jackrabbit Tonneau Cover TR2003 on your 2006 Chevrolet Silverado 2500HD with the 6-1/2' bed requires the replacement cover #PE22KV.

view full answer...

Answer 2

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 3

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 8

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 9

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 10

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...